Bedienungsanleitung Garmin ECHOMAP Ultra serie (Seite 43 von 52) (Englisch)

691420

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Synchronizing the Fuel Data with the Actual Vessel

Fuel

You can synchronize the fuel levels in the chartplotter with the

actual fuel in the vessel when you add fuel to your vessel.

Select Gauges > Engine > Menu.

Select an option:

• After you have filled up all the fuel tanks on the vessel,

select Fill Up All Tanks. The fuel level is reset to

maximum capacity.

• After you have added less than a full tank of fuel, select

Add Fuel to Boat, and enter the amount added.

• To specify the total fuel in the vessel tanks, select Set

Total Fuel Onboard, and enter the total amount of fuel in

the tanks.

Customizing Engine Gauge and Fuel Gauge Limits

You can configure the upper and lower limits and the range of

desired standard operation of a gauge.

NOTE: Not all options are available for all gauges.

From an applicable gauges screen, select Menu > Gauge

Setup > Set Gauge Limits.

Select a gauge to customize.

Select Gauge Limits > Custom.

Select an option:

• To set the minimum value of the standard operating

range, select Rated Min..

• To set the maximum value of the standard operating

range, select Rated Max..

• To set the lower limit of the gauge lower than the rated

minimum, select Scale Min..

• To set the upper limit of the gauge higher than the rated

maximum, select Scale Max..

Select the limit value.

Repeat steps 4 and 5 to set additional gauge limits.

Communications Settings

NOTE: Some settings and options require additional charts or

hardware.

Select Settings > Communications.

Serial Port: Sets the input/output format for the serial port to

use when connecting the chartplotter to external NMEA

devices, computers, or other Garmin devices.

NMEA 0183 Setup: Sets the NMEA 0183 sentences the

chartplotter transmits, how many digits to the right of the

decimal point are transmitted in a NMEA output, and how

waypoints are identified (NMEA 0183 Settings, page 37).

NMEA 2000 Setup: Allows you to view and label the devices on

the NMEA 2000 network (NMEA 2000 Settings, page 37).

Marine Network: Allows you to view the devices with which you

are sharing maps, sonar, or radar. Not available on all

chartplotter models.

NOTE: You can only view networked data on a model that

supports that data. For example, you cannot view networked

radar on model that does not support radar.

Wireless Devices: Allows you set up wireless devices (Setting

Up the Wi

‑

Fi Wireless Network, page 37). Not available on

all chartplotter models.

Wi-Fi Network: Allows you set up the Wi‑Fi network (Setting Up

the Wi

‑

Fi Wireless Network, page 37).

NMEA 0183

The chartplotters support the NMEA 0183 standard, which is

used to connect various NMEA 0183 devices, such as VHF

radios, NMEA instruments, autopilots, wind sensors, and

heading sensors.

To connect the chartplotter to optional NMEA 0183 devices, see

the chartplotter installation instructions.

The approved NMEA 0183 sentences for the chartplotter are

GPAPB, GPBOD, GPBWC, GPGGA, GPGLL, GPGSA, GPGSV,

GPRMB, GPRMC, GPRTE, GPVTG, GPWPL, GPXTE, and

Garmin proprietary sentences PGRME, PGRMM, and PGRMZ.

This chartplotter also includes support for the WPL sentence,

DSC, and sonar NMEA 0183 input with support for the DPT

(depth) or DBT, MTW (water temperature), and VHW (water

temperature, speed, and heading) sentences.

NMEA 0183 Settings

Select Settings > Communications > NMEA 0183 Setup.

Sounder: Enables NMEA 0183 output sentences for the

sounder (if applicable).

Route: Enables NMEA 0183 output sentences for routes.

System: Enables NMEA 0183 output sentences for system

information.

Garmin: Enables NMEA 0183 output sentences for Garmin

proprietary sentences.

Posn Precision: Adjusts the number of digits to the right of the

decimal point for transmission of NMEA output.

Waypoint IDs: Sets the device to transmit waypoint names or

numbers via NMEA 0183 while navigating. Using numbers

may resolve compatibility issues with older NMEA 0183

autopilots.

Diagnostics: Displays NMEA 0183 diagnostic information.

Defaults: Restores the NMEA 0183 settings to the original

factory defaults.

NMEA 2000 Settings

Select Settings > Communications > NMEA 2000 Setup.

Device List: Displays the devices connected to the network.

Label Devices: Changes the labels for available connected

devices.

Naming Devices and Sensors on the Network

You can name devices and sensors connected to the Garmin

Marine Network and the NMEA 2000 network.

Select Settings > Communications.

Select Marine Network or NMEA 2000 Setup > Device List.

Select a device from the list on the left.

Select Change Name.

Enter the name, and select Done.

Wi‑Fi Network

Setting Up the Wi

‑

Fi Wireless Network

The chartplotters can create a Wi‑Fi network to which you can

connect wireless devices. The first time you access the wireless

network settings, you are prompted to set up the network.

Select Settings > Communications > Wireless Devices >

Wi-Fi Network > Wi-Fi > On > OK.

If necessary, enter a name for this wireless network.

Enter a password.

You will need this password to access the wireless network

from a wireless device. The password is case-sensitive.

Connecting a Wireless Device to the Chartplotter

Before you can connect a wireless device to the chartplotter

wireless network, you must configure the chartplotter wireless

network (Setting Up the Wi

‑

Fi Wireless Network, page 37).

You can connect multiple wireless devices to the chartplotter to

share data.

Device Configuration 37

Garmin ECHOMAP Ultra serie Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin ECHOMAP Ultra serie

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info