Bedienungsanleitung Garmin Edge 1030 Plus (Seite 7 von 36) (Englisch)

725378

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Press down slightly and turn the Edge device clockwise until

it locks into place.

Releasing the Edge

Turn the Edge clockwise to unlock the device.

Lift the Edge off the mount.

Installing the Mountain Bike Mount

NOTE: If you do not have this mount, you can skip this task.

Select a secure location to mount the Edge device where it

does not interfere with the safe operation of your bike.

Use the 3 mm hex key to remove the screw from the

handlebar connector .

Select an option:

• If the handlebar diameter is 25.4 mm, place the thicker

pad around the handlebar.

• If the handlebar diameter is 31.8 mm, place the thinner

pad around the handlebar.

• If the handlebar diameter is 35 mm, do not use a rubber

pad.

Place the handlebar connector around the handlebar, so that

the mount arm is above the bike stem.

Use the 3 mm hex key to loosen the screw on the mount

arm, position the mount arm, and tighten the screw.

NOTE: Garmin recommends tightening the screw so the

mount arm is secure, with a maximum torque specification of

20 lbf-in. (2.26 N-m). You should check the tightness of the

screw periodically.

If necessary, use the 2 mm hex key to remove the two

screws on the back side of the mount , remove and rotate

the connector, and replace the screws to change the

orientation of the mount.

Replace and tighten the screw on the handlebar connector.

NOTE: Garmin recommends tightening the screw so the

mount is secure, with a maximum torque specification of

7 lbf-in. (0.8 N-m). You should check the tightness of the

screw periodically.

Align the tabs on the back of the Edge device with the bike

mount notches .

Press down slightly and turn the Edge device clockwise until

it locks into place.

Acquiring Satellite Signals

The device may need a clear view of the sky to acquire satellite

signals. The time and date are set automatically based on the

GPS position.

TIP: For more information about GPS, go to www.garmin.com

/aboutGPS.

Go outdoors to an open area.

The front of the device should be oriented toward the sky.

Wait while the device locates satellites.

It may take 30–60 seconds to locate satellite signals.

Training

Going for a Ride

If you are using a wireless sensor or accessory, it can be paired

and activated during initial setup (Pairing Your Wireless

Sensors, page 17). If your device was packaged with a

wireless sensor, they are already paired and can be activated

during initial setup.

Hold to turn on the device.

Go outside, and wait while the device locates satellites.

The satellite bars turn green when the device is ready.

From the home screen, select or to select an activity

profile.

Select .

Select to start the activity timer.

Training 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Edge 1030 Plus Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Edge 1030 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info