Bedienungsanleitung Garmin GHC 20 (Seite 5 von 8) (Englisch)

590084

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

GPS Steering Patterns

WARNING

You are responsible for the safe operation of your boat. Do not

begin a GPS pattern until you are certain that the water is clear

of obstacles.

CAUTION

Garmin

recommends using Follow Route only under motor

power. Using Follow Route while under sail can cause an

unexpected gybe, risking damage to your sailboat. Unattended

sails and rigging can be damaged or cause injury to any crew or

passengers during an unexpected gybe maneuver.

NOTE: The autopilot must be connected to a NMEA 2000

NMEA

0183 compatible chartplotter to follow a GPS steering

pattern.

The autopilot can steer the boat along a route defined by your

GPS device or in preset patterns based on a GPS location

(waypoint). To use GPS steering, you must have a compatible

GPS device connected to the autopilot using NMEA 2000 or

NMEA 0183. GPS steering patterns are based on a GPS

waypoint to which you are actively navigating using your

optional GPS device. This waypoint is called the active

waypoint.

Following a GPS Steering Route

The autopilot can steer the boat according to a route defined on

a compatible GPS device.

Create and navigate a route on your GPS device.

Select Menu > GPS Steering > Follow Route.

Orbit Pattern

The orbit pattern steers the boat in a continuous circle around

the active waypoint. The size of the circle is defined by your

distance from the active waypoint when you begin the orbit

pattern.

Following an Orbit Pattern

Select Menu > GPS Steering > Orbit > Engage.

Select an option:

• Select to begin a clockwise turn.

• Select to begin a counter-clockwise turn.

Cloverleaf Pattern

The cloverleaf pattern steers the boat to repeatedly pass over

an active waypoint. When you begin the cloverleaf pattern, the

autopilot drives the boat toward the active waypoint and begins

the cloverleaf pattern.

Setting Up the Cloverleaf Pattern

You can adjust the distance from the waypoint at which the

autopilot turns your boat for another pass over the waypoint.

The default setting turns the boat at a range of 1000 ft. (300 m)

from the active waypoint.

between the waypoint and the location where the autopilot turns

the boat

Select Menu > GPS Steering > Cloverleaf > Length.

Select or to set the range.

Select Done.

Following the Cloverleaf Pattern

Select Menu > GPS Steering > Cloverleaf > Engage.

Select an option:

• To begin a starboard turn, select .

• To begin a port turn, select .

Search Pattern

The search pattern steers the boat in increasingly larger circles

outward from the active waypoint, forming a spiral pattern.

When you begin the search pattern, the autopilot drives the boat

to the active waypoint and begins the pattern.

Setting Up the Search Pattern

You can adjust the distance between each circle in the spiral.

The default distance between circles in 50 ft. (20 m).

Select Menu > GPS Steering > Search > Spacing.

Select or to set the distance.

Select Done.

Following the Search Pattern

Select Menu > GPS Steering > Search > Engage.

Select an option:

• To begin a starboard turn, select .

• To begin a port turn, select .

Sailboat Autopilot Operation

CAUTION

When engaged, the autopilot controls only the rudder. You and

your crew remain responsible for the sails while the autopilot is

engaged.

In addition to heading hold, you can use the autopilot to

maintain a wind hold. You can also use the autopilot to control

the rudder while tacking and gybing.

Wind Hold

You can set the autopilot to maintain a specific bearing relative

to the current wind angle. Your device must be connected to a

NMEA 2000 or NMEA 0183 compatible wind sensor to perform

a wind hold or a wind-based tack or gybe.

Setting the Wind Hold Type

Before you can enable the wind hold type, you must connect a

NMEA 2000 or NMEA 0183 wind sensor to the autopilot.

For advanced autopilot configuration, see the installation

instructions included with your autopilot.

Select Menu > Setup > User Autopilot Setup > Wind Hold

Type.

Select Apparent or True.

Engaging Wind Hold

Before you can enable the wind hold type, you must connect a

NMEA 2000 or NMEA 0183 wind sensor to the autopilot.

When the autopilot is in standby mode, select Wind Hold.

Engaging Wind Hold from Heading Hold

Before you can enable the wind hold type, you must connect a

NMEA 2000 or NMEA 0183 wind sensor to the autopilot.

With heading hold engaged, select Menu > Wind Hold.

Adjusting the Wind Hold Angle with the Autopilot

You can adjust the wind hold angle on the autopilot when wind

hold is engaged.

• To adjust the wind hold angle in increments of 1°, select

<<10° <1° or 1°> 10°>>.

• To adjust the wind hold angle in increments of 10°, hold

<<10° <1° or 1°> 10°>>.

Tack and Gybe

You can set the autopilot to perform a tack or gybe while

heading hold or wind hold is engaged.

Tacking and Gybing from Heading Hold

Engage heading hold (page 1).

Select Menu > Tack/Gybe.

Select or to choose a direction.

Sailboat Autopilot Operation 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GHC 20 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GHC 20

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info