Bedienungsanleitung Garmin GHC 20 (Seite 6 von 8) (Englisch)

590084

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

The autopilot steers your boat through a tack or gybe, and

"Tacking" displays on the heading screen until the maneuver

is complete.

Tacking and Gybing from Wind Hold

Before you can engage wind hold, you must have a wind sensor

installed.

Engage wind hold (page 3).

Select Menu > Tack/Gybe.

Select TACK or GYBE.

The autopilot steers your boat through a tack or gybe, and

information about the progress of the tack or gybe appears

on the screen.

Setting a Tack and Gybe Delay

The tack and gybe delay allows you to delay steering a tack and

gybe after you initiate the maneuver.

Select Menu > Setup > User Autopilot Setup > Sailing

Configuration > Tack/Gybe Delay.

Select or to determine the length of the delay (from 0 to

15 seconds).

Select Done.

Enabling the Gybe Inhibitor

NOTE: The gybe inhibitor does not prevent you from manually

performing a gybe using the helm or step steering.

The gybe inhibitor prevents the autopilot from performing a

gybe.

Select Menu > Setup > User Autopilot Setup > Sailing

Configuration > Gybe Inhibitor.

Select Enabled.

Device Configuration

User Autopilot Settings

Select Menu > Setup > User Autopilot Setup.

Power Mode: Sets the device power mode to normal or

economy mode. Economy power mode allows you to set the

percentage of power used to run the autopilot.

Power Saver: Controls the aggressiveness of the autopilot. The

autopilot makes fewer adjustments in power saver mode.

Configuring the Remote Control

NOTE: The Garmin quatix™ watch can be configured to act as a

remote control for the helm control. See the instructions that

came with the watch for more information.

You can connect one optional remote control to the helm

control.

Select Menu > Setup > Remote.

Searching for a Remote Control

Select Menu > Setup > Remote > Search for Remote.

Pairing a Remote

Search for a remote control (page 4).

Begin pairing the remote control according to the instructions

that came with that accessory.

A message appears on the helm control after the remote has

been paired successfully.

Select Connect.

Assigning Remote Button Actions

CAUTION

If you assign a pattern to a button on the remote control,

remember that you are responsible for the safe operation of

your boat. Do not begin a pattern until you are certain the water

is clear of obstacles.

NOTE: If you assign direction control functionality to a button on

the remote, the autopilot must be in standby mode to change

the direction (forward or reverse).

Select Menu > Setup > Remote.

Select a remote button to assign an action to.

Select a button action.

If necessary, repeat steps 2 and 3 for the remaining buttons.

Disconnecting a Remote Control

Select Menu > Setup > Remote.

Select Disconnect Remote.

Display Settings

Select Menu > Setup > Display.

Color Mode: Sets the device to display day or night colors.

Configure Colors: Sets the color configuration for each color

mode. For day color mode, you can select a full color or high

contrast color configuration. For night color mode, you can

select a full color, red and black, or green and black color

configuration.

Backlight: Sets the backlight level.

Network Sharing: Allows you to share color mode, color

configuration, and backlight settings with other devices

across the NMEA 2000 network.

System Settings

Select Menu > Setup > System.

Units: Sets the units of measure.

Heading: Sets the reference used in calculating heading

information.

Variance: Adjusts the variance from true north. This setting is

only available when the heading is set to True.

Beeper: Sets if and when audible sounds are used.

Auto Power: Enables the device to turn on automatically when

the NMEA 2000 network turns on.

GHC Low Volt. Alarm: Sounds an alarm when the voltage of

the power supply connected to the device drops below a

specified level.

Language: Sets the on-screen language.

Operating Mode: Allows you to set the operating mode to

normal or store demo mode.

System Information: Allows you to view software information.

Factory Defaults: Resets the unit to factory defaults.

4 Device Configuration

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GHC 20 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GHC 20

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info