Bedienungsanleitung Garmin GNX 130 (Seite 7 von 12) (Englisch)

691469

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Configuring the Beeper

You can configure the beeper to sound when the keys are

pressed.

Select > SETUP > SYSTEM > BEEPER.

Configuring the Position Format

NOTE: Do not change the position format or the map datum

unless you are using a map or chart that specifies a different

position format.

Select > SETUP > SYSTEM > GPS POSITION.

Select an option:

• To change the position format in which a reading appears,

select POSITION FORMAT.

• To change the coordinate system on which the map is

structured, select MAP DATUM.

Display Settings

Select > SETUP > DISPLAY.

BACKLIGHT: Sets the backlight brightness.

COLOR: Sets the screen color.

NETWORK SHARING: Shares color, backlight, and beeper

settings with devices across the NMEA 2000 network.

Configuring Data Sources

Sensors connected to your instrument provide data, such as

wind or speed information, and can be configured through your

instrument. See the owner's manual for each sensor for more

information.

Select > SETUP > DATA SOURCES.

Select a data category.

If more than one sensor on the boat provides data from the

category, select a sensor to configure.

Select a configuration option, and configure the setting.

Resolving a Combined Network

When the device is turned on, it can detect when it has been

synchronized with instruments on another network. This can

happen if the device has previously been installed on another

vessel and synchronized with instruments on the other vessel's

network. If the settings are not restored to the factory default

values (Restoring Profiles to their Default Settings, page 1), the

device detects a conflict that must be resolved.

Select > SETUP > COMBINED NETWORKS

DETECTED.

Select an option:

• To synchronize existing instruments on the network to the

device, select NO.

• To synchronize the device to existing instruments on the

network, select YES.

Keypad Operation

The keypad can control all of the compatible marine instruments

on your NMEA 2000 network. All compatible marine instruments

must be connected to the same NMEA 2000 network, and you

can configure the order in which they are controlled.

NOTE: The keypad is not compatible with all Garmin marine

instruments. For a complete list of compatible instruments, go to

www.garmin.com/GNXkeypad.

Button Function

Select to cycle backlight levels on the marine

instruments and keypads.

Hold to place the marine instruments and keypads into

sleep mode.

through

Presets. Select to make all displays switch to a

configured preset page.

Select to switch the marine instrument you control using

the keypad.

Select to cycle the pages on the selected marine

instrument.

Setting up an Instrument for Use with the

Keypad

All compatible marine instruments you need to control with the

keypad must be connected to the same NMEA 2000 network as

the keypad.

You should perform this procedure for each compatible

instrument you add to the NMEA 2000 network.

On a compatible marine instrument connected to the same

NMEA 2000 network as the keypad, select > SETUP >

REMOTE KEYPAD SETUP.

NOTE: If COMBINED NETWORKS DETECTED is shown

instead of REMOTE KEYPAD SETUP, the combined network

must be resolved before you can control the instrument with

the keypad (Resolving a Combined Network, page 3).

Select YES to enable keypad control on the instrument.

Repeat steps 1 through 2 for each additional compatible

instrument you need to control with the keypad.

Setting up the Keypad Display Order

You can configure how the keypad cycles through connected

marine instruments with the buttons.

On a compatible marine instrument connected to the same

NMEA 2000 network as the keypad, select > SETUP >

REMOTE KEYPAD SETUP > SET UP DISPLAY ORDER.

The device scans the network for other connected

instruments.

NOTE: The location of the device in the current display order

is shown to the right of the SET UP DISPLAY ORDER menu

item. For example, if the device is second in a series of four

devices, 2:4 is shown in the menu.

Select an option:

• If a correct number of connected instruments is shown,

select CONTINUE.

• If an incorrect number of connected instruments is shown,

check the power and connections of all compatible

instruments, and select RETRY.

Keypad Operation 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GNX 130 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GNX 130

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info