Bedienungsanleitung Garmin GPSMAP 800 (Seite 43 von 52) (Englisch)

544282

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Skyview: Shows the relative position of GPS satellites in the

sky.

GLONASS: Turns on or off GLONASS usage (Russia satellite

system). When the system is used in situations with poor sky

visibility, this configuration can be used in combination with

GPS to provide more accurate position information.

WAAS/EGNOS: Turns on or off WAAS (in North America) or

EGNOS (in Europe), which can provide more-accurate GPS

position information. When using WAAS or EGNOS, the

device may take longer to acquire satellites.

Speed Filter: Averages the speed of your vessel over a short

period of time for smoother speed values.

Source: Allows you to select the preferred source for GPS.

Viewing the Event Log

The event log shows a list of system events.

Select Settings > System > System Information > Event

Log.

Viewing System Software Information

You can view the software version, the basemap version, all

supplemental map information (if applicable), the software

version for an optional Garmin radar (if applicable), and the unit

ID number. You may need this information to update the system

software or to purchase additional map data information.

Select Settings > System > System Information >

Software Information.

My Vessel Settings

NOTE: Some settings and options require additional charts or

hardware.

Select Settings > My Vessel.

Keel Offset: Offsets the surface reading for the depth of a keel,

making it possible to measure depth from the bottom of the

keel instead of from the transducer location (Setting the Keel

Offset, page 23).

Temp. Offset: Compensates for the water temperature reading

from a NMEA 0183 water-temperature sensor or a

temperature-capable transducer (Setting the Water

Temperature Offset, page 37).

Calibrate Water Speed: Calibrates the speed-sensing

transducer or sensor (Calibrating a Water Speed Device,

page 37).

Fuel Capacity: Sets the combined fuel capacity of all the fuel

tanks on your vessel ( Setting the Fuel Capacity of the

Vessel, page 28).

Vessel Type: Enables some chartplotter features based on the

boat type.

Fill Up All Tanks: Sets the tank levels to full (Synchronizing the

Fuel Data with the Actual Vessel Fuel, page 28).

Add Fuel to Boat: Allows you to enter the quantity of fuel you

added to your tank, when you did not entirely fill up the tank

(Synchronizing the Fuel Data with the Actual Vessel Fuel,

page 28).

Set Total Fuel Onboard: Sets the combined amount of fuel in

all the fuel tanks on your vessel (Synchronizing the Fuel Data

with the Actual Vessel Fuel, page 28).

Set Gauge Limits: Sets the upper and lower limits of various

gauges (Customizing Engine Gauge and Fuel Gauge Limits,

page 27).

Setting the Keel Offset

You can enter a keel offset to compensate the surface reading

for the depth of a keel, making it possible to measure depth from

the bottom of the keel instead of from the transducer location.

Enter a positive number to offset for a keel. You can enter a

negative number to compensate for a large vessel that may

draw several feet of water.

Complete an action, based on the location of the transducer:

• If the transducer is installed at the water line

, measure

the distance from the transducer location to the keel of the

boat. Enter this value in steps 3 and 4 as a positive

number.

• If the transducer is installed at the bottom of the keel

measure the distance from the transducer to the water

line. Enter this value in steps 3 and 4 as a negative

number.

Select Settings > My Vessel > Keel Offset.

Select or based on the location of the transducer.

Enter the distance measured in step 1.

Setting the Water Temperature Offset

Before you can set the water temperature offset, you must have

a NMEA 0183 water-temperature sensor or a temperature-

capable transducer to measure water temperature.

The temperature offset compensates for the temperature

reading from a temperature sensor.

Measure the water temperature using the temperature sensor

or temperature-capable transducer that is connected to the

chartplotter.

Measure the water temperature using a different temperature

sensor or a thermometer that is known to be accurate.

Subtract the water temperature measured in step 1 from the

water temperature measured in step 2.

This is the temperature offset. Enter this value in step 5 as a

positive number if the sensor connected to the chartplotter

measures the water temperature as being colder than it

actually is. Enter this value in step 5 as a negative number if

the sensor connected to the chartplotter measures the water

temperature as being warmer than it actually is.

Select Settings > My Vessel > Temp. Offset.

Enter the temperature offset calculated in step 3.

Calibrating a Water Speed Device

If you have a speed-sensing transducer connected to the

chartplotter, you can calibrate that speed-sensing device to

improve the accuracy of water-speed data displayed by the

chartplotter.

Select Settings > My Vessel > Calibrate Water Speed.

Follow the on-screen instructions.

If the boat is not moving fast enough or the speed sensor is

not registering a speed, a message appears.

Select OK, and safely increase the boat speed.

Device Configuration 37

Garmin GPSMAP 800 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GPSMAP 800

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info