Bedienungsanleitung Garmin GPSMAP 8417 MFD (Seite 25 von 62) (Englisch)

658523

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

Select Settings > My Vessel > Depth and Anchoring >

Keel Offset.

Select or based on the location of the transducer.

Enter the distance measured in step 1.

Sailboat Autopilot Operation

CAUTION

When engaged, the autopilot controls only the rudder. You and

your crew remain responsible for the sails while the autopilot is

engaged.

In addition to heading hold, you can use the autopilot to maintain

a wind hold. You can also use the autopilot to control the rudder

while tacking and gybing.

Wind Hold

You can set the autopilot to maintain a specific bearing relative

to the current wind angle. Your device must be connected to a

NMEA 2000

or NMEA

0183 compatible wind sensor to perform

a wind hold or a wind-based tack or gybe.

Setting the Wind Hold Type

Before you can enable the wind hold type, you must connect a

NMEA 2000

or NMEA 0183 wind sensor to the autopilot.

For advanced autopilot configuration, see the installation

instructions included with your autopilot.

From the autopilot screen, select Menu > Autopilot Setup >

Wind Hold Type.

Select Apparent

or True.

Engaging Wind Hold

Before you can enable the wind hold type, you must connect a

NMEA 2000 or

NMEA 0183 wind sensor to the autopilot.

When the autopilot is in standby mode, select Wind Hold.

Engaging Wind Hold from Heading Hold

Before you can enable the wind hold type, you must connect a

NMEA 2000 or

NMEA 0183 wind sensor to the autopilot.

With heading hold engaged, select

Menu >

Wind Hold

Adjusting the Wind Hold Angle with the Autopilot

You can adjust the wind hold angle on the autopilot when wind

hold is engaged.

• To adjust the wind hold angle in increments of 1°, select or

• To adjust the wind hold angle in increments of 10°, hold or

Tack and Gybe

You can set the autopilot to perform a tack or gybe while

heading hold or wind hold is engaged.

Tacking and Gybing from Heading Hold

Engage heading hold (Engaging the Autopilot,

page

29).

Select Menu >

Tack/Gybe

Select a direction.

The autopilot steers your boat through a tack or gybe.

Tacking and Gybing from Wind Hold

Before you can engage wind hold, you must have a wind sensor

installed.

Engage wind hold (Engaging Wind Hold, page 17).

Select Menu

> Tack/Gybe

Select Tack

or Gybe.

The autopilot steers your boat through a tack or gybe, and

information about the progress of the tack or gybe appears

on the screen.

Setting a Tack and Gybe Delay

The tack and gybe delay allows you to delay steering a tack and

gybe after you initiate the maneuver.

From the autopilot screen, select Menu > Autopilot Setup >

Sailing Setup >

Tack Delay

Select the length of the delay.

If necessary, select Done.

Enabling the Gybe Inhibitor

NOTE:

The gybe inhibitor does not prevent you from manually

performing a gybe using the helm or step steering.

The gybe inhibitor prevents the autopilot from performing a

gybe.

From the autopilot screen, select Menu > Autopilot Setup >

Sailing Setup >

Gybe Inhibitor

Select

Enabled.

Sonar

When properly connected to an optional Garmin

sounder

module and a transducer, your compatible chartplotter can be

used as a fishfinder. Different sonar views can help you view the

fish in the area.

The adjustments you can make to each sonar view vary

depending on the view you are in and the chartplotter model,

sounder module, and transducer you have connected.

For more information about which transducer is best for your

needs, go to

www.garmin.com/transducers.

Sonar Views

The sonar views available vary depending on the type of

transducer and optional sounder module connected to the

chartplotter. For example, you can view the Split Frequency

view only if you have a dual-frequency transducer connected.

There are four basic styles of sonar views available: a full-

screen view, a split-screen view that combines two or more

views, a split-zoom view, and a split-frequency view that

displays two different frequencies. You can customize the

settings for each view in the screen. For example, if you are

viewing the split-frequency view, you can separately adjust the

gain for each frequency.

If you do not see an arrangement of sonar views to suit your

needs, you can create a custom combination screen (

Adding a

Custom Combination Screen, page 3) or a SmartMode layout

(Adding a SmartMode

Layout, page

Traditional Sonar View

There are several full-screen views available, depending on the

equipment connected.

Sonar 17

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin GPSMAP 8417 MFD Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin GPSMAP 8417 MFD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info