Bedienungsanleitung Garmin Striker 5 (Seite 9 von 16) (Englisch)

657482

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

option provides a good balance between a quickly

scrolling image and targets that are less distorted.

Setting the Bottom Search Limit

You can set a maximum depth at which the auto range feature

searches for the bottom. A lower limit acquires data about the

bottom faster than a higher limit.

From a sonar screen, select > Sonar Setup > Bottom

Search Limit.

Select a range.

Sonar Appearance Settings

From a sonar view, select > Sonar Setup > Appearance.

Color Scheme: Sets the color scheme.

Edge: Highlights the strongest signal from the bottom to help

define the hardness or softness of the signal.

A-Scope: Displays a vertical flasher along the right side of the

screen that shows instantaneously the range to targets along

a scale.

Fish Symbols: Sets how the sonar interprets suspended

targets.

Turning on the A-Scope

The a-scope is a vertical flasher along the right side of the full-

screen sonar view. This feature expands the most recently

received sonar data so that it is easier to see. It can also be

helpful for detecting fish that are close to the bottom.

NOTE: This feature is not available on all sonar screens.

From the full screen page, select > Sonar Setup >

Appearance > A-Scope.

A-Scope

Diameter of the sonar cone at the present depth

Configuring the Appearance of Suspended Targets

NOTE: Configuring the appearance of suspended targets on

one screen applies that setting to all screens.

NOTE: This feature is not available on all sonar views.

Shows suspended targets as symbols.

Shows suspended targets as symbols with target depth

information.

Shows suspended targets as symbols with background sonar

information.

Shows suspended targets as symbols with background sonar

information and target depth information.

From a sonar screen, select > Sonar Setup >

Appearance > Fish Symbols.

Select an option.

Sonar Noise Rejection Settings

From a sonar view, select > Sonar Setup > Noise Reject.

Interference: Adjusts the sensitivity to reduce the effects of

interference from nearby sources of noise.

When you adjust the interference setting from off

through

low

, medium

, and high

, noise is gradually removed,

but there is little effect on the strong target returns. You

should use the lowest interference setting that achieves the

desired improvement to remove interference from the screen.

Correcting installation issues that cause noise is the best way

to eliminate interference.

Surface Noise: Hides sonar returns near the surface of the

water. Hiding surface noise helps reduce screen clutter.

Surface noise

is caused by interference between the

transducer and water. You can hide surface noise

to help

reduce clutter. Wider beam widths (lower frequencies) can

show more targets, but can generate more surface noise.

TVG: Reduces surface noise.

This control is best used for situations when you want to

control and suppress clutter or noise near the water surface.

It also allows for the display of targets near the surface that

are otherwise hidden or masked by surface noise.

Overlay Number Settings

You can customize the data shown on the sonar screen.

NOTE: Not all features are available on all devices.

From a sonar screen, select > Overlay Numbers.

Navigation Inset: Shows the navigation inset when the vessel

is navigating to a destination.

Device Voltage: Shows the voltage of the device.

Speed: Shows the vessel's current speed.

Time of Day: Shows the current time of day.

Compass Tape: Shows the compass tape data bar.

Depth: Shows the transducer's current depth.

Water Temp.: Shows the current water temperature.

Waypoints

Waypoints are locations you record and store in the device.

Marking Your Present Location as a

Waypoint

From any screen, select .

Waypoints 5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Striker 5 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Striker 5

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info