Bedienungsanleitung Garmin Striker Vivid (Seite 16 von 20) (Englisch)

740398

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Setting Alarms

CAUTION

The Beeper setting must be turned on to make alarms audible

(Setting the Beeper, page 2). Failure to set audible alarms could

lead to injury or property damage.

Navigation Alarms

Select Settings > Alarms > Navigation.

Arrival: Sets an alarm to sound when you are within a specified

distance or time from a turn or a destination.

Anchor Drag: Sets an alarm to sound when you exceed a

specified drift distance while anchored.

Off Course: Sets an alarm to sound when you are off course by

a specified distance.

System Alarms

Alarm Clock: Sets an alarm clock.

Device Voltage: Sets an alarm to sound when the battery

reaches a specified low voltage.

GPS Accuracy: Sets an alarm to sound when the GPS location

accuracy falls outside the user-defined value.

Sonar Alarms

Select Settings > Alarms > Sonar.

Shallow Water: Sounds when the water depth is shallower than

the specified depth.

Deep Water: Sounds when the water depth is deeper than the

specified depth.

Water Temp.: Sounds when the water temperature varies more

than ± 2°F (± 1.1°C). Alarm settings are saved when the

device is turned off.

NOTE: You must connect the device to a temperature-

capable transducer to use this alarm.

Fish

Fish: Sets an alarm to sound when the device detects a

suspended target.

• sets the alarm to sound when fish of all sizes are

detected.

• sets the alarm to sound only when medium or large

fish are detected.

• sets the alarm to sound only when large fish are

detected.

Unit Settings

Select Settings > Units.

System Units: Sets the unit format for the device.

Variance: Sets the magnetic declination, the angle between

magnetic north and true north, for your present location.

North Reference: Sets the direction references used in

calculating heading information. True sets geographic north

as the north reference. Grid sets grid north as the north

reference (000º). Magnetic sets the magnetic north as the

north reference.

Position Format: Sets the position format in which a given

location reading appears. Do not change this setting unless

you are using a map or chart that specifies a different

position format.

Map Datum: Sets the coordinate system on which the map is

structured. Do not change this setting unless you are using a

map or chart that specifies a different map datum.

Time Format: Sets a 12-hour, 24-hour, or UTC time format.

Time Zone: Sets the time zone.

Daylight Savings Time: Sets daylight savings time to Off or On.

Navigation Settings

NOTE: Some settings and options require additional hardware.

Select Settings > Navigation.

Route Labels: Sets the type of labels shown with route turns on

the map.

Turn Transition Activ.: Sets the turn transition to be calculated

based on time or distance.

Turn Transition Time: Sets how many minutes before the turn

that you transition to it as the next leg, when Time is selected

for the Turn Transition Activ. setting.

Turn Transition Dist.: Sets how far before the turn that you

transition to it as the next leg, when Distance is selected for

the Turn Transition Activ. setting.

Route Start: Selects a starting point for route navigation. You

can select Boat to start navigation from the current vessel

location, or Waypoints to start from the first waypoint on the

route.

Restoring the Factory Default Settings

NOTE: This deletes all settings information you have entered,

including all Garmin Quickdraw Contours you have generated.

Select Settings > System > System Information > Reset >

Reset Settings > Yes.

Sharing and Managing User Data

WARNING

This feature allows you to import data from other devices that

may have been generated by third parties. Garmin makes no

representations about the accuracy, completeness, or timeliness

of data that is generated by third parties. Any reliance on or use

of such data is at your own risk.

You can share user data between compatible devices. User

data includes waypoints, saved tracks, routes, and boundaries.

• You can share data if two compatible devices are connected

using the blue and brown wires on the power cable or using

the User Data Sharing Cable (Connecting to a Garmin

Device to Share User Data, page 12).

Connecting to a Garmin Device to Share

User Data

You can connect the STRIKER Vivid device to a compatible

Garmin device to share user data, such as waypoints. If the

devices are mounted near each other, you can connect the blue

and brown wires. If the devices are mounted too far apart for the

wires to reach, you can connect the devices using a User Data

Sharing Cable (010-12234-06).

Make sure both devices are connected to the same ground.

Complete an action:

• If the devices are mounted near each other, connect the

blue wire from the first device to the brown wire of the

second, and connect the brown wire from the first device

to the blue wire of the second.

• If the devices are not mounted near each other, obtain a

User Data Sharing Cable (010-12234-06), and connect

the devices following the instructions included with the

cable (User Data Sharing Cable Wiring Diagram,

page 13).

On both devices, select User Data > Manage Data > User

Data Sharing.

User data is shared between the connected devices. If you

select Clear User Data, data is removed from both connected

devices.

12 Sharing and Managing User Data

Garmin Striker Vivid Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Striker Vivid

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info