Bedienungsanleitung Garmin TR-1 Gladiator (Seite 13 von 36) (Englisch)

583791

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Change Heading Using Zigzags

If you program the [Plus (+)] button for Zigzags (Fig 3) ,and you then press

the [Plus(+)] button the pilot will begin to zigzag about the heading you

were on when you pressed the button. The zigzag angle and period are both

programmable. An example zigzag path is shown in the  gure below. When the

system is doing zigzags, it will return to heading hold if either the [Left Arrow],

[Right Arrow] or [Plus(+)] buttons are pressed.

Heading Hold

Boat Path

Change Heading with Zigzags

If you program the Idle/Resume button for Zigzags (other), then when you press the Idle/Resume

button the pilot will begin to zigzag about the heading you were on when you pressed the button. The

zigzag angle and period are both programmable. An example zigzag path is shown in the figure below.

Automatic idle and resume is accomplished by pressing the Idle/Resume button. If the throttle is set

higher than idle, the Idle/ Resume function will take the engine to idle. If the throttle is sitting in the

idle position, the Idle/Resume function will return the throttle to the last "above idle" position. The

Idle/Resume button must be programmed to perform Idle/Resume and not MOB or Zigzags.

Idle/Resume

Increase throttle by pressing the Up Arrow button. Decrease throttle by pressing the Down Arrow

button. The electric throttle runs in parallel with the tiller throttle, this means that you can't reduce

the RPM with the electric throttle if the tiller throttle is set high. It is best to always run with the tiller

throttle set to idle. Be careful to set the electric throttle and tiller throttle to closed position before startin

your outboard.

Throttle Up/Down

To engage Zigzags:

1) Press and hold the [Setup] button.

2) Press and light up the [number 2, Zigzag] LED on the handheld.

3) Release the [Setup] Button.

To start the zigzags, press and release the [Zigzag/Plus (+)] button on the

handheld, the autopilot will start the zig-zags.

Factory default sets the zig-zags at 30 degrees per zig-zag and the cycle

time is 3 minutes. If you wish to change those settings refer to the setup

codes below and refer to [Code 8] for the Amplitude (Degree of turn) 10

choices; 5 to 50 degrees by 5’s. [Code 9] The Zig-zag period (Length/Time)

has 20 choices from 1/2 to 10 minutes by 1/2’s.

Fig 3

Description

Code Setup Options (Parameters) Factory Settings

Zigzag Amplitude (Degree of turn) 8 10 choices/ 5 to 50 Degrees by 5’s 30 degrees

Zigzag Period (Length) 9 20 choices 1/2 to 10 minutes by 1/2’s 1.5 minutes

To change the setup options for zigzags:

You must be in [Auto] or [STBY] mode before selection process can start

1. Press and release the [Setup] Button. The [Setup] LED will illuminate to

indicate the system is ready to take setup commands (button pushes).

2. Select the Setup Code you want to use by pressing and releasing the button labeled 8 or 9 until the

appropriate LED is lit. (See the Codes and Setup Choices on the table below.

3. Increase an adjustable parameter one step by each press of the [UP Arrow] button. When the parameter is

adjusted to its maximum value, the [Up Arrow] LED will light. The parameter is adjusted and is in use by the

autopilot immediately.

4. Decrease an adjustable parameter one step by each press of the [Down Arrow] button. When the

parameter is adjusted to its minimum value, the [Down Arrow] LED will light. The parameter is adjusted and

is in use by the autopilot immediately.

5. To save the changes into permanent memory and make the selected function into a

startup default: Press and release the [Setup] button (the [Setup] LED should be lit),

and then press and hold the [Select Load] button. While holding down the [Select Load]

button, press and release the [Deckmount] On/Off button quickly, then release the GPS

[Select Load] button.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin TR-1 Gladiator Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info