Bedienungsanleitung Garmin Vector 2S (Seite 6 von 16) (Englisch)

589622

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Installing the Left Pedal and Pedal Pod

This procedure is for the Vector S system.

Apply a thin layer of grease on the pedal spindle threads

Insert the spindle into the crank arm

Hand tighten the spindle.

NOTE: The left pedal spindle has a left-handed (reverse)

thread.

Use the pedal wrench to tighten the spindle.

NOTE: Garmin recommends torque of 25 to 30 lbf-ft. (34 to

40 N-m).

Clean all excess grease from the spindle using a clean cloth

and soapy water or isopropyl alcohol.

Place the pedal pod

on the spindle.

NOTE: You must carefully bend the cable

out of the way.

The pedal pod should be flat against the crank arm.

TIP: Power and cadence calculations are not impacted by the

orientation of the pedal pod. Garmin recommends placing the

pedal pod on the leading edge of the crank. When the crank

is in the forward position, the pedal pod should be pointing

downward.

Firmly plug the cable into the spindle.

Insert the screw

into the pedal pod, and use the 2.5 mm

hex key to tighten the screw.

Rotate the crank arm to check for clearance.

The pedal pod should not interfere with any part of the bike.

Installing the Right Pedal

This procedure is for the Vector S system.

Apply a thin layer of grease on the pedal spindle threads.

Insert the spindle into the crank arm.

Hand tighten the spindle.

Use the pedal wrench to tighten the spindle.

NOTE: Garmin recommends torque of 25 to 30 lbf-ft. (34 to

40 N-m).

Installing the Shoe Cleats

NOTE: The left and right cleats are the same.

Apply a thin layer of grease on the cleat bolt threads.

Align the cleat

, washers

, and bolts

Use a 4 mm hex key to loosely attach each bolt to the sole of

the shoe.

Adjust the cleat to the shoe in your preferred position.

This can be adjusted after a trial ride.

Tighten the cleat firmly to the shoe.

NOTE: Garmin recommends torque of 4 to 6 lbf-ft. (5 to 8 N-

m).

Adjusting the Release Tension

NOTICE

Do not overtighten the release tension screw on the bottom of

the pedal. The release tension should be adjusted equally for

both pedals.

Use a 3 mm hex key to adjust the release tension of each

pedal.

There is a window on the back of the pedal binding that

shows the allowable range.

Paring Vector with Your Edge 1000

Before you can view Vector data on the Edge device, you must

pair the devices.

Pairing is the connecting of ANT+

wireless sensors. This

procedure contains instructions for the Edge 1000. If you have

another compatible device, see Other Compatible Devices, or

go to www.garmin.com/vectorowner.

Bring the Edge device within range (3 m) of the sensor.

NOTE: Stay 10 m away from other ANT+ sensors while

pairing.

Turn on the Edge device.

From the home screen, select > Sensors > Add Sensor >

Power.

Rotate the crank arm a few times.

Select your sensor.

When the sensor is paired with your Edge device, a message

appears, and the sensor status is Connected. You can

customize a data field to display Vector data.

Pedal Pod Status LED

Multiple green LED flashes indicate a system issue that requires

your attention.

NOTE: When the pedal pod battery is low, the status LED

flashes red, instead of green.

LED Activity Status

1 green flash every 10

seconds.

The Vector system is working properly.

2 flashes every 10 seconds. The pedal is not connected.

3 flashes every 10 seconds. The pedal pod is connected, but it

cannot communicate with the Edge

device.

4 flashes every 10 seconds. The pedal pod is searching for the

other pedal pod.

5 flashes every 10 seconds. The installation angle is not set or

cannot be detected.

6 flashes every 10 seconds. There is a hardware installation error.

7 flashes every 10 seconds. There is a software update in progress.

1 red flash every 10 seconds. The pedal pod battery is low.

Your First Ride

Before you ride with Vector for the first time, you must enter the

crank length and set the installation angle of the sensors inside

the pedals. The Vector system automatically calibrates after

each ride. You must also enter the crank length when you move

Vector to another bike.

This procedure contains instructions for the Edge 1000 device. If

you have another compatible device, see Other Compatible

Devices, or go to www.garmin.com/vectorowner.

Entering the Crank Length

The crank length is often printed on the crank arm.

2 Introduction

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Vector 2S Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info