Bedienungsanleitung Garmin Vector (Seite 6 von 14) (Englisch)

589619

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

3On the pedal spindle, stack the pedal pod and any required

washers Â.

TIP: You must carefully bend the cable Ã out of the way.

4Insert the spindle into the crank arm Ä.

5Hand tighten the spindle.

NOTE: The left pedal spindle has a left-handed (reverse)

thread.

TIP: Power and cadence calculations are not impacted by

the orientation of the pedal pod. Garmin® recommends

placement of the pedal pod on the leading edge of the crank.

When the crank is in the forward position, the pedal pod

should be pointing downward.

6Rotate the crank arm to check for clearance.

The pedal pod should not interfere with any part of the bike.

7Use the pedal wrench to tighten the spindle.

NOTE: Garmin recommends torque of 25 to 30 lbf-ft. (34 to

40 N-m).

8Firmly plug the cable into the spindle.

9Rotate the crank arm to check for clearance.

10Repeat steps 2–9 to install the right pedal.

NOTE: If the pedal pod cable rubs the chain, you can add

one or two washers between the pedal pod and the crank

arm to increase clearance.

Installing the Left Pedal and Pedal Pod

This procedure is for the Vector S system.

1Apply a thin layer of grease on the pedal spindle À and the

pedal pod Á where it contacts the pedal spindle.

2On the pedal spindle, stack the pedal pod and any required

washers Â.

NOTE: You must carefully bend the cable Ã out of the way.

NOTE: Do not use more than two washers.

3Insert the spindle into the crank arm Ä.

4Hand tighten the spindle.

NOTE: The left pedal spindle has a left-handed (reverse)

thread.

TIP: Power and cadence calculations are not impacted by

the orientation of the pedal pod. Garmin recommends

placement of the pedal pod on the leading edge of the crank.

When the crank is in the forward position, the pedal pod

should be pointing downward.

5Rotate the crank arm to check for clearance.

The pedal pod should not interfere with any part of the bike.

6Use the pedal wrench to tighten the spindle.

NOTE: Garmin recommends torque of 25 to 30 lbf-ft. (34 to

40 N-m).

7Firmly plug the cable into the spindle.

8Rotate the crank arm to check for clearance.

Installing the Right Pedal

This procedure is for the Vector S system.

1Apply a thin layer of grease on the pedal spindle.

2Insert the spindle into the crank arm.

NOTE: If you used one or two washers on the left pedal, use

the same amount on the right pedal.

3Hand tighten the spindle.

4Use the pedal wrench to tighten the spindle.

NOTE: Garmin recommends torque of 25 to 30 lbf-ft. (34 to

40 N-m).

Installing the Shoe Cleats

NOTE: The left and right cleats are the same.

1Apply a thin layer of grease on the cleat bolt threads.

2Align the cleat À, washers Á, and bolts Â.

3Use a 4 mm hex key to loosely attach each bolt to the sole of

the shoe.

4Adjust the cleat to the shoe in your preferred position.

This can be adjusted after a trial ride.

5Tighten the cleat firmly to the shoe.

NOTE: Garmin recommends torque of 4 to 6 lbf-ft. (5 to 8 N-

m).

Adjusting the Release Tension

NOTICE

Do not overtighten the release tension screw on the bottom of

the pedal. The release tension should be adjusted equally for

both pedals.

Use a 3 mm hex key to adjust the release tension of each

pedal.

There is a window on the back of the pedal binding that

shows the allowable range.

Paring Vector with Your Edge 1000

Before you can view Vector data on the Edge device, you must

pair the devices.

Pairing is the connecting of ANT+™ wireless sensors. This

procedure contains instructions for the Edge 1000. If you have

another compatible device, see Edge 810 and 510 Device

Instructions, or go to www.garmin.com/vectorowner.

1Bring the Edge device within range (3 m) of the sensor.

NOTE: Stay 10 m away from other ANT+ sensors while

pairing.

2Turn on the Edge device.

2 Introduction

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Vector Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Vector

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info