Bedienungsanleitung Garmin Vector (Seite 7 von 14) (Englisch)

589619

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

3From the home screen, select > Sensors > Add Sensor >

Power.

4Rotate the crank arm a few times.

When the sensor is paired with your Edge device, the sensor

status is Connected. You can customize a data field to display

Vector data.

Your First Ride

Before you ride with Vector for the first time, you must enter the

crank length, set the installation angle of the sensors inside the

pedals, and calibrate the static zero reference. You must also

calibrate the system if you move Vector to another bike.

These procedures contain instructions for the Edge 1000. If you

have another compatible device, see Edge 810 and 510 Device

Instructions, or go to www.garmin.com/vectorowner.

Entering the Crank Length

The crank length is often printed on the crank arm.

1Rotate the pedals a few times in order to activate Vector.

2From the home screen, select > Sensors > > Sensor

Details > Crank Length.

3Enter the crank length, and select .

Setting the Installation Angle

Before you set the installation angles, you must set the Edge

data fields to display power and cadence.

1Go for a short ride on a trainer or on the road.

2Ride until the cadence is nearly 70 rpm.

3Accelerate smoothly to approximately 90 rpm.

When the installation angles are successfully set, a message

appears and data fields display power data on the Edge

device (1000, 810, and 510 only).

Performing a Static Zero Calibration

NOTE: During this task, the bike must be in an upright position,

and nothing can be touching the pedals.

1From the home screen, select the status bar or swipe down

from the top of the screen.

The connections page appears.

2Select > Calibrate.

When the zero reference is determined, a message appears

on the Edge device.

Calibrating Vector Before Each Ride

For best results, Garmin recommends calibrating Vector at the

start of every ride.

1Perform a static zero calibration.

2Go for a ride.

Customizing the Data Fields

This procedure contains instructions for the Edge 1000, 810,

800, and 510 devices. If you have another compatible device,

see Edge 500 Device Instructions.

1Hold a data field to change it.

2Select a category.

3Select a data field.

Training

Pedal-Based Power

Vector measures pedal-based power.

Vector measures the force you apply a few hundred times every

second. Vector also measures your cadence or rotational

pedaling speed. By measuring the force, the direction of force,

the rotation of the crank arm, and time, Vector can determine

power (watts). Because Vector independently measures left and

right leg power, it reports your left-right power balance.

NOTE: The Vector S system does not provide left-right power

balance.

Maintenance Tips

NOTICE

Some bike tools may scratch the finish of Vector components.

• Use wax paper or a towel between the tool and the

hardware.

• After any bike adjustments, rotate the crank arm to check for

clearance.

• Calibrate Vector at the start of every ride (Calibrating Vector

Before Each Ride).

• Keep Vector components clean.

• When moving Vector to another bike, clean the threads and

surfaces thoroughly.

• Go to www.garmin.com/vectorowner for the latest updates

and information.

Vector Data

Your ride data or history is recorded to your Edge.

NOTE: History is not recorded while the timer is stopped or

paused.

When the device memory is full, a message appears. The

device does not automatically delete or overwrite your history.

Upload your history to Garmin Connect™ periodically to keep

track of all your ride data.

Sending Your Ride to Garmin Connect

NOTICE

To prevent corrosion, thoroughly dry the USB port, the weather

cap, and the surrounding area before charging or connecting to

a computer.

1Pull up the weather cap À from the USB port Á.

2Plug the small end of the USB cable into the USB port on the

device.

3Plug the large end of the USB cable into a computer USB

port.

4Go to www.garminconnect.com/start.

5Follow the on-screen instructions.

Garmin Connect

You can connect with your friends on Garmin Connect. Garmin

Connect gives you the tools to track, analyze, share, and

encourage each other. Record the events of your active lifestyle

including runs, walks, rides, swims, hikes, triathlons, and more.

To sign up for a free account, go to www.garminconnect.com

/start.

Store your activities: After you complete and save an activity

with your device, you can upload that activity to Garmin

Connect and keep it as long as you want.

Training 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Vector Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Vector

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info