Bedienungsanleitung Garmin Zumo XT (Seite 6 von 30) (Englisch)

730371

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

Vehicle mode

Motorcycle mode

Off-road mode

Choosing a Transportation Mode

Select the transportation mode icon on the status bar.

Using the Large Button Keyboard

You can enable additional keyboard languages or layouts in the

language and keyboard settings .

• Select or to view more characters.

• Select to switch to other keyboard languages and layouts.

Installation

Mounting your device in a motorcycle

Powered Motorcycle Mount

WARNING

Garmin

strongly recommends having an experienced installer

with the proper knowledge of electrical systems install the

device. Incorrectly wiring the power cable can result in damage

to the vehicle or the battery and can cause bodily injury.

See the Important safety and product information guide in the

product box for product warnings and other important

information.

The device must be mounted in a suitable and secure location

on your motorcycle, based on available power sources and safe

cable routing. No fuse is required.

Motorcycle mount

10 to 30 Vdc system power (red)

System ground (black)

NOTE: additional parts are included with the device to provide

more installation and wiring options. Contact an experienced

installer for more information about using these parts with your

motorcycle.

Crimp-Style Ring Terminal: connects the wiring harness

directly to the battery terminal.

Cable Tie: secures cables to the motorcycle frame.

Installing the Handlebar Base

The device includes parts for two handlebar installation

solutions. Custom mounts may require additional hardware.

Installing the U-bolt and Handlebar Base

Place the U-bolt around the handlebar , and thread the

ends through the handlebar base .

Tighten the nuts to secure the base.

NOTE: the recommended torque is 50 lbf-in (5.65 N-m). Do

not exceed torque of 80 lbf-in (9.04 N-m).

Installing the Handlebar Base to the Clutch-Clamp or Brake-

Clamp Brackets

Remove the two factory bolts on your clutch-clamp or brake-

clamp bracket .

NOTE: both 1/4 in. (65 mm) standard and M6 bolts are

included. Match the size of the factory bolts on your clutch-

clamp or brake-clamp bracket.

Thread the new bolts through the handlebar base, spacers

, and clutch-clamp or brake-clamp bracket.

Tighten the bolts to secure the base.

Attaching the Power Cables to the Motorcycle Mount

Thread the power cable connector through the opening

in the motorcycle mount.

Pull the cable back until it is snug.

Screw the black screw into the back of the mount to

hold the cable in place.

NOTE: an additional replacement screw is included in the

box.

Attaching the Base Plate to the Motorcycle Mount

NOTICE

Direct, sustained contact with the base plate or any part of the

motorcycle may damage the mount over time. To prevent this

kind of damage, you must place the mounting spacers between

the mount and base plate, and make sure that no part of the

device or mount touches the motorcycle.

2 Installation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Zumo XT Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Garmin Zumo XT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info