Bedienungsanleitung Gastroback 40977 (Seite 50 von 65) (Deutsch, Englisch)

714637

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

EN EN

98 99

8. Holding the feed chute of the mincer in the 2'clock position, insert the coupling

of the mincer with the protruding hexagonal shaft into the mincer coupling of the

mixing arm. If required, turn the mincer to and fro a little until it slides into the

mincer coupling.

9. While pressing the release button of the mincer coupling, turn the mincer coun-

ter-clockwise to the stop. The feed chute must face upwards vertically and the

mincer must be engaged firmly when releasing the release button.

10. Place the tablet onto the feed chute of the mincer and push it down carefully.

The mincer is now ready for operation.

Mincing Your Food

11. Prepare a portion of your food and place the food onto the tablet of the mincer.

Hold the provided container or another sufficiently large bowl at hand.

12. Connect the machine to a suitable wall power outlet (see: ‘Important Safegu-

ards for Electrical Appliances’). The display areas show dashes and an acoustic

signal sounds. The stand mixer is in standby mode now.

WARNING – Do not hold your hands or any foreign objects (e.g. cooking

utensils) into the feed chute of the mincer or at the mixing drive, while the machine

is connected to the power supply. Always use the provided pusher for pushing

down your food within the feed chute.

13. Hold the control dial pressed for approx. 2 seconds for switching on the machi-

ne. A signal sounds and “00” flashes on the speed display. The operating time

display shows the default operating time: “20:00” (20 minutes).

14. When you wish to be reminded to making breaks in time, you should set the

timer of the machine to 10 minutes (see: ‘Operating Time and Pause Function’).

15. Turn the control dial until the speed setting “10” is shown at the speed display.

NOTE

The worm shaft moves the food to the outlet automatically, as soon as the motor

is running. Your food should fit easily into the feed chute and fall onto the worm

shaft. Therefore, in most cases, it is not necessary to push your food down. Only

use the pusher, when your food clogs the feed chute and/or sticks to the walls of

the feed chute.

16. It is best to hold the container below the outlet of the mincer, while pushing the

pieces of food one by one from the tablet into the opening of the feed chute. If

required, use the pusher to push your food down slowly and without much pressure.

IMPORTANT - Cut tough pieces of food (e.g. meat) in stripes of approx. 2 x 2 x

6 cm. Dough for pasta, sausage, kebab, and cookies should be kneaded to a thick

roll of approx. 2 x 2 cm in diameter. The food must fit conveniently into the feed chute.

PROCESSING TOUGH FOOD – MINCING MEAT

The cross blade and steel mincing discs are intended for processing tough food,

especially raw meat. The pieces of food are crushed via the worm shaft and cut

via the cross blade, before the food is pressed though the mincing disc. The typical

consistency of minced meat is the result. By selecting the appropriate mincing disc,

you get different grind sizes. For getting a really fine product, you may process the

food repeatedly.

IMPORTANT - Always use only one separate mincing disc at a time. When a finer

consistency is required, process the food twice, selecting the fine mincing disc for

the second run.

Preparing the Mincer

1. Prepare your food for mincing. Remove all hard and inedible parts (e.g. bones,

gristle, tendons). Cut your food to stripes of 2 x 2 x 6 cm.

2. Hold the mincer housing with the thread facing upwards and insert the worm shaft with

the long, hexagonal shaft facing downwards. With the worm shaft inserted correctly,

the hexagonal shaft protrudes the mincer housing at the coupling side (bottom).

IMPORTANT - The blades of the cross blade are edged only at one side. Ensure to

insert the cross blade in correct orientation. The edged side is supposed to cut your

food just at the mincing disc. Handle the cross blade with care to avoid injuries.

3. With the sharp edges facing upwards, place the cross blade on the short cen-

tral pin of the worm shaft. If required, turn the cross blade until it settles without

a gap on the worm shaft.

4. Select the required mincing disc (coarse, medium, or fine) and place it on the

worm shaft. With the worm shaft and cross blade mounted correctly, you can

turn the mincing disc until the spigots at the rim of the mincing disc engage in

the notches at the rim of the mincer housing.

5. Turn the screw ring hand-tight on the mincer housing, but without violence.

6. Prepare the machine for operation (see: ‘Preparation’).

7. For removing the protecting cover of the mincer coupling at the mixing arm, turn

the protecting cover clockwise and pull it out.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gastroback 40977 Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info