Bedienungsanleitung Gastroback 40977 (Seite 48 von 65) (Deutsch, Englisch)

714637

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

EN EN

94 95

IMPORTANT - Before installing the mixing tool, always ensure that the opening

on top of the mixing tool shaft is clean and dry. Otherwise, the drive shaft of the

mixing drive could get polluted and/or damaged.

NOTE

Always move the mixing arm to the upper position, for inserting or removing the

mixing tools.

1. Ensure that the appliance is unplugged. Then move the mixing arm into the

upper position (see: ‘Preparation’).

2. Disassembling the mixing tool: Holding the mixing arm with one hand, push

the installed mixing tool upwards until you can turn the mixing tool easily clock-

wise (to the right). Then pull the mixing tool down off the drive shaft (see: ‘After

Usage / Removing the Mixing Tools’).

3. Assembling a mixing tool: Align the groove on top of the mixing tool shaft with

the securing pin on the drive shaft of the mixing drive. Holding the mixing arm

with one hand, push the mixing tool upwards until you can turn the mixing tool

easily counter-clockwise (to the left). Ensure that the mixing tool is locked securely

and cannot fall out/down.

4. Lower the mixing arm to the operating position. For this, hold the mixing arm

tightly at the front and press the unlock button. Ensuring that your hand stays

away from the joint of the mixing arm, gently lower the mixer arm to the opera-

ting position. Slide the splash guard into position on top of the mixing bowl and

gently press the splash guard down for fixing it on the mixing bowl.

NOTE

You may turn the splash guard to almost every required position. There is no need

to remove the splash guard for adding further ingredients. Simply fill the ingredients

in via the feed opening. Too large pieces of food should be cut to smaller pieces

fitting easily into the feed opening (e.g. cooked potatoes for purée).

STARTING THE MIXING PROCESS

NOTE

Use the splash guard to avoid that clouds of powdery ingredients and splashes

escape during operation. Turn the feed opening to the desired position. Liquid

ingredients, powder, and small pieces can be filled in via the feed opening. Add

flour in portions to the mixing bowl and use a low speed setting (1-2) until the sin-

gle portions are mixed in, for minimizing the build-up of flour dust.

1. Prepare the machine for operation (see: ‘Preparation’ and ‘Using the Mixing

Function’). Ensure that the mixing arm is correctly locked in the horizontal opera-

ting position. Connect the machine to a suitable wall power outlet (see: ‘Impor-

tant Safeguards for Electrical Appliances’). A beep sounds an the speed display

and operating time display show dashes. The stand mixer is now in standby

mode and ready for use.

WARNING – Do not hold your hands or any foreign objects (e.g. rubber

spatula) into the mixing bowl or on the mixing tool, while the machine is connected

to the power supply. Always switch off the machine (press the control dial), before

manually scraping down your food in the mixing bowl.

2. Press the control dial for approx. 2 seconds for switching on the machine. A

signal sounds, the bowl illumination goes on, and the display areas show the

defaults: speed “00” and operating time “20:00”.

NOTE

Start with low speed settings (1 or 2), until the ingredients are combined. This

will minimize splashing and avoid clouds of powdery ingredients (e.g. flour). The

machine supports you in this via the smart motor control. The motor does not start

with a jolt, but increases the speed slowly to the set value. Therefore, when selec-

ting the speed, always wait for some seconds, until the selected speed is reached.

IMPORTANT - Do not leave the motor operate continuously for more than 10

minutes to avoid overheating. Make breaks of at least 5 minutes after each 10

minutes of operation.

3. When the required mixing time is known already, you may adjust the operating

time accordingly. Use the arrow keys at the left side of the operating time display

to enter the desired time. The machine stops operation automatically, when the

set operating time ran out (see: ‘Operating Time and Pause Function’).

4. Turn the control dial clockwise for starting operation. As soon as the motor starts,

the count-down of the operating time starts.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gastroback 40977 Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info