Bedienungsanleitung Gastroback 40977 (Seite 47 von 65) (Deutsch, Englisch)

714637

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

EN EN

92 93

PREPARING THE MACHINE FOR OPERATION

CAUTION – Do not hold your hand onto the joint of the back pillar and mixing

arm to avoid crushing your hand in the joint. The mixing arm is heavy and could

cause damage when falling down from the upper position. For moving the mixing

arm up or down, always grasp the mixing arm at the front. Always ensure that the

mixing arm is engaged securely, before releasing your grip at the mixing arm.

IMPORTANT - Always lower the mixing arm to the horizontal (operating) position,

when the machine is not in use and for moving the machine. When moving the

machine, keep in mind that the machine is very heavy and the suction cups fix the

machine to the work surface.

1. Grasp the machine at the front and backside of the base plate and place the

machine on a suitable surface (see: ‘Important Safeguards’).

2. Grasp the front of the mixing arm, while pressing the unlock button. Doing so,

ensure to keep your hands away from the joint of the mixing arm. Move the

mixing arm to the upper position and, releasing the unlock button, ensure that the

mixing arm is locked securely in the upper position before releasing your grip.

IMPORTANT - Do not operate the machine without the mixing bowl locked in

place, even when using the mincer. Only when using the mixing function: Fill

your food into the mixing bowl, according to your recipe. Further ingredients may

be filled in during operation via the feed opening in the splash guard. Place the

mixing bowl into the bowl holder at the base plate. The MAX filling line should be

at the rear of the machine. If required, turn the mixing bowl to and fro a little to

make the mixing bowl slide down into the excavation at the base plate. Then turn

the mixing bowl counter-clockwise to the stop to lock it securely in place.

With your left hand, hold the mixing arm at the front and, while pressing the unlock

button, slowly move the mixing arm to the lower operating position. Only when using

the mincer: Place the splash guard onto the mixing bowl for protecting the mixing

drive against unintended touch. If required, carefully and completely pull the power

cord out of the cord storage at the back pillar of the stand mixer. The power cord

is approx. 1m in length. There may be no loops of the power cord within the cord

storage, while the machine is in use.

USING THE MIXING FUNCTION

WARNING – Do not grasp into the mixing bowl or hold any foreign objects

(e.g. cooking utensils) into the mixing bowl or at the mixing tools, while the motor

is running. Always switch off the motor (press the control dial) and unplug the

machine, before touching the mixing tool, assembling or disassembling any parts,

inserting your hands or any foreign objects into the mixing bowl or moving the

mixing arm to the upper position.

Before plugging in the power plug and switching on by pressing the control dial:

Always ensure that no foreign utensils (e.g. cooking utensils) are inside the mixing

bowl and the mixing arm is in the lower (operating) position. IDo not process more

than 1500 g flour plus approx. 900 ml water in continuous operation for more than

10 minutes. If your recipe demands more than this, process your food in portions

and make breaks for at least 5 minutes after each 10 minutes of operation, to avoid

overloading the motor.

IMPORTANT - Do not operate the mixing function in combination with the mincer

to avoid overloading the motor.

ASSEMBLING OR DISASSEMBLING THE MIXING TOOL

On top of the mixing tool shaft, there is an opening with a bent guiding groove. At

the bottom of the mixing drive, two drive shafts are protruding, each one equipped

with a securing pin. For assembling the mixing tool, the guiding groove must be

slipped over the securing pin and locked by turning the mixing tool. The drive shafts

are completely identical and you may install the mixing tool at any one of them.

The kneading tools (dough hook and dough paddle) may be used separately or in

combination with each other.

NOTE

It may occur that the mixing drive comes to a standstill in an unfortunate position,

making it impossible to install both kneading tools in combination. In this case,

simply install the kneading tools each at the other drive shaft.

CAUTION – Do not attempt to install the wire whisk or scraper beater in

combination with any other mixing tool! Otherwise, the mixing tool and/or

mixing drive could get damaged. Do not let the mixing arm fall down into the low-

er operating position. Always hold the mixing arm at the front when pressing the

unlock button for moving the mixing arm. Always ensure to keep your hands and

fingers away from the joint between mixing arm and back pillar of the machi-

ne to avoid crushing your hand.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gastroback 40977 Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info