Bedienungsanleitung Gazco Ashdon - Electric (Seite 5 von 28) (Englisch)

813468

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Thermostatic Control

2.21 The appliance is fitted with a thermostat, see Diagram 1,

which can control the room temperature between

approximately 9˚C and 34˚C. The edge of the thermostat

control dial is numbered 1 - 9 with 1 being the coolest

setting and 9 being the warmest. If the room temperature is

too high turn the thermostat dial in an anti-clockwise

direction. If the room temperature is too low turn the dial in a

clockwise direction.

Log Effect

2.22 Log effect appliances have a glass fibre fuel bed which

may give off a slight smell when first used. This is

normal and should disappear after a day or two.

Thermal Safety Cutout

The appliance is fitted with a thermal safety cutout,

which operates if it overheats. If this happens:

2.23 Unplug the appliance and allow it to cool for 5 - 10

minutes.

2.24 Check the air inlets/outlets for any obstruction and clear, see

Maintenance, Section 3.4.

2.25 Plug in appliance and switch it on. The cutout will re-set

and the appliance should function correctly. If this is not

the case:

2.26 Unplug once more and have the fire checked by a

competent electrician.

3. Maintenance

3.1 ALWAYS UNPLUG FROM MAINS SUPPLY BEFORE

CLEANING OR UNDERTAKING ANY MAINTENANCE.

CLEANING

3.2 Only clean the outer casing when it is cold. Do not use

abrasive cleaners.

3.3 For painted castings, wipe with a damp cloth and buff

with a lint free duster.

CLEANING AIR INLETS

3.4 Ensure the appliance is unplugged.

3.5 Clean the air inlet and outlet grilles regularly with a soft

cloth or the nozzle of a vacuum cleaner.

Dust build-up can inhibit efficient performance of the

fan and lead to the safety cut-out operating.

3.6 Keep the area around the stove clean and free of fluff, dust

or pet hair.

3.7 In particular, build-up of dust etc. can occur around the

heater area under the appliance. Take particular care to

keep this area free from such particles on a regular basis

to prevent build-up.

CLEANING LOG MOULDING

3.8 Ensure the appliance is unplugged and cold before handling

log moulding.

3.9 Follow Section 4, choosing relevant model, to access and

remove log moulding.

3.10 Dust off any build-up with a brush or damp cloth and

replace.

4. Removing & Replacing Doors and

Removal of Fuel Bed

WARNING: DOOR CASTINGS ARE EXTREMELY

HEAVY - SEEK ASSISTANCE BEFORE REMOVAL.

Please note: The fuel bed is secured by 2 x screws on

the lower panel on the front of the stove.

Screws

Fuel bed

Take care not to damage the plastic screen when

replacing the fuel bed.

4.1 Small or Medium Marlborough

Small or Medium Stockton

Medium Ashdon

4.1.1 Remove nuts from door facia holding the door before

removing final nut, see Diagram 4a.

4.1.2 Remove the screws on the lower panel on the front of the

appliance and carefully remove the fuel bed, see

Diagram 3.

User Instructions

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gazco Ashdon - Electric Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gazco Ashdon - Electric

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info