Bedienungsanleitung Gazco F40 Avanti Conventional Coal (Seite 4 von 23) (Englisch)

813396

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

1. GENERAL

1.1 Installation and servicing must be carried out by a

competent person in accordance with Gas Safety

(Installation and Use) Regulations 1998, the relevant

British Standards for Installation, appropriate Codes of

Practice and in accordance with the manufacturers

instructions. It is recommended that a CORGI registered

engineer be used for this purpose as they are approved

by the HSE under the above regulations.

1.2 This appliance is suitable for use in G.B. and I.E. using

Natural Gas at a supply pressure of 20mbar or LPG at a

supply pressure of 29mbar (Butane) or 37mbar (propane).

1.3 The installation shall also be completed in accordance with:

– The Building Regulations issued by The Department of

The Environment.

– The Building Standards (Scotland) Regulations issued by

the Scottish Development Department.

For Republic of Ireland, reference should be made to the

relevant standards governing installations (IS813:1996)

1.4 Read all these instructions before commencing installation.

1.5 This appliance must be installed in accordance with the

rules in force and only used in a sufficiently ventilated

space.

1.6 Ensure that curtains are not positioned above the stove, and

that there is at least a clearance of 300mm between the

sides of the stove and any curtains.

1.7 The manufacturer considers the full outer casing of this

stove to be a working surface. Therefore it will become hot

whilst in operation. A suitable guard is recommended to

protect young children, the aged and the infirm.

1.8 This stove must only be operated with the door secured

firmly in position. If any cracks appear in the glass the

appliance must not be used until the glass panel is replaced.

1.9 Do not attempt to burn rubbish in this stove.

1.10 Any combustible shelves or surrounding furniture must only

be fitted in accordance with the minimum dimensions

detailed in diagram 1.

AR1468

1.11 Contact a competent service engineer to carry out relevant

spillage checks etc. following home improvements carried

out after installation of this stove (e.g. the fitting of double

glazing).

1.12 In all correspondence, please quote the appliance type and

serial number which can be found on the databadge at the

rear of the stove.

1.13 This product is guaranteed for 2 years from the date of

installation, as set out in the terms and conditions of sale

between Gazco and your local Gazco dealer. Please consult

with your local Gazco dealer if you have any questions. In

all correspondence always quote the model No. and serial

No. Please ensure the commissioning checklist is

completed by your installer, as this is a requirement of

your Guarantee.

2. LIGHTING THE STOVE

2.1 Locate the control valve on the appliance. There are two

control knobs on the valve, the right-hand knob controls the

pilot ignition and the left-hand knob controls the main

burner.

2.2 If your appliance has already been upgraded to battery

remote control, please refer to the instructions provided with

the upgrade to operate the remote control. The following

instructions will work for either situation.

AR0914

2.3 Ensure that the left-hand control knob is pointing to off ( )

2.4 Ensure that the right-hand control knob is pointing to off ( ).

2.5 Press in the right-hand control knob and rotate it anti-

clockwise until a click is heard (keep pressing in) and the

knob is pointing to pilot ( ). The pilot should now light. If

the pilot has not lit, repeat the procedure until it does.

2.6 Keep the control knob pressed in for 10 seconds and then

release it, the pilot should stay alight. If the pilot goes out,

repeat the procedure until does.

2.7 If the pilot will not light after repeated attempts, contact the

retailer or installer from whom the appliance was purchased.

2.8 Turn the right-hand control to point to main burner ( ) .

The appliance can now be controlled using the left- hand

control knob.

2.9 Turn the left-hand control knob to point to low fire ( ) the

main burner will light on low. The burner can now be

controlled between low and high settings. Turn the control

knob anti-clockwise to increase the flame height and

clockwise to decrease the flame height.

THE YELLOW FLAMES WILL APPEAR WHEN THE FIRE

HAS GAINED SUFFICIENT HEAT - TYPICALLY 10 TO 20

MINUTES.

IF THE APPLIANCE IS EXTINGUISHED OR GOES OUT IN

USE, WAIT 3 MINUTES BEFORE ATTEMPTING TO

RELIGHT THE APPLIANCE.

USER INSTRUCTIONS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gazco F40 Avanti Conventional Coal Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info