Bedienungsanleitung Gazco F40 Avanti Conventional Coal (Seite 12 von 23) (Englisch)

813396

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

definite flow into the chimney, proceed with the

installation, if not warm the chimney for a few minutes.

IF THERE IS STILL NO DEFINITE FLOW, THE FLUE MAY

REQUIRE ATTENTION - SEEK EXPERT ADVICE.

3.14 The flue system may now be connected to the stove, ensure

that all joints are sealed with a suitable fire resistant sealant.

It is also recommended that a physical retention method be

used at the flue spigot joint, self-tapping screws being

favoured.

3.15 Connect a suitable pressure gauge to the test point located

on the inlet fitting, and turn the gas supply on. Light the

stove and check all gas joints for gas soundness. Turn the

stove to maximum and check that the supply pressure is as

stated on the data badge. Turn the gas off and replace the

test point screw, turn the gas on and check the test point for

gas soundness.

4. HANDLING & DISPOSAL OF FIRE

CERAMICS

The fuel effect and side panels in this appliance are made

from Refractory Ceramic Fibre (RCF), a material which is

commonly used for this application.

Protective clothing is not required when handling these

articles, but we recommend you follow normal hygiene rules

of not smoking, eating or drinking in the work area and

always wash your hands before eating or drinking.

To ensure that the release of RCF fibres are kept to a

minimum, during installation and servicing a HEPA filtered

vacuum is recommended to remove any dust accumulated

in and around the appliance before and after working on it.

When servicing the appliance it is recommended that the

replaced items are not broken up, but are sealed within

heavy duty polythene bags and labelled as RCF waste.

RCF waste is classed as stable, non-reactive hazardous waste

and may be disposed of at a licensed landfill site.

Excessive exposure to these materials may cause temporary

irritation to eyes, skin and respiratory tract; wash hands

thoroughly after handling the material.

5. FUEL BED ARRANGEMENT

5.1 Place the flame baffle onto the burner and push against the

rear tray lip. See diagram 9.

AR0359

5.2 Locate the rear panel against the spacer brackets and slide

down so that it locates on the ledge of the flame baffle. See

diagram 10.

AR0360

5.3 Locate the front coal between the heat shield and the flame

baffle so its ends sit flat on the burner skin. See diagram 11.

AR0361

5.4 Place five of the loose round coals on the front coal so they

lean against the flame baffle, in between the fingers. Place

the two rectangular coals against the reflector panels, one

either side, behind the front row of loose coals. See diagram

12.

AR0362

5.5 Place four of the loose round coals behind the first row so

that they sit on the fingers, the two outer ones should touch

the rectangular coals. See diagram 13.

AR0363

INSTALLATION INSTRUCTIONS

INSTALLATION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gazco F40 Avanti Conventional Coal Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info