Bedienungsanleitung Gazco Riva 2 F670 Balanced Flue (Seite 6 von 44) (Englisch)

813406

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

2.8 P1 - Program 1 for a Timed Setting

Press the SET button until the TIMER mode is displayed.

Hold the SET button. The displays flashes the current time

for P1. While the time displayed is flashing you can alter

the hours and minutes set.

To set the time your appliance first lights, change P1

— Press the UP button to alter the hour.

— Press the DOWN button to alter the minutes in 10

minute increments.

Press SET again to move to the end setting for P1 This is

the time your Studio first shuts down:

— Press the UP button to alter the hour.

— Press the DOWN button to alter the minutes.

2.9 P2 - Program 2 for a Timed Setting

Use the same steps outlined in 2.8 to change the setting

for P2.

If you have already set P1 and want to alter the setting for

P2 only:

— Press the SET button until TIMER mode is displayed.

— Hold the SET button until the display flashes the

current time for P1 .

— Press the SET button once again to scroll past the

settings for P1 and P1.

With the time still flashing:

— Press the UP button to alter the hour.

— Press the DOWN button to alter the minutes.

Once all four times are set press the OFF button.

2.10 To view existing settings:

— Select Timer Mode.

— Press and briefly hold the SET button you see the start

time for P1.

— Repeat the above step for the start and end of each

program.

Low Battery

“BATT” is displayed on the remote when its batteries need

replacement.

Setting the time

Simultaneously press the up and down buttons.

Press the up button to set the hour and the down button to

set the minutes.

Press OFF to return to the manual mode or simply wait.

Setting the °C/24 Hour or °F/12 Hour clock

Press OFF and the down arrow until the display changes

from °C/24 hour clock to °F/12 hour clock and vice versa.

If the remote is removed, lost or damaged, signals

transmitted to the receiver cease. Your appliance will

go to standby (pilot) mode after 6 hours.

Troubleshooting

IMPORTANT: In the unlikely event that the handset

fails to communicate correctly with the appliance

it may be necessary to turn off the gas supply at

the isolation valve until any problems can be

resolved.

The gas meter and isolation valve can be located

outside in a meter box, under the stairs, beneath

the kitchen sink or in the garage. Whilst this list is

not exhaustive, it is important to be able to

identify the location of the valve in case of any

gas emergency.

To turn off the gas supply, simply turn the handle

so the lever is at 90 degrees to the upright gas

pipe.

If you smell gas, open doors and windows and

never operate any electrical switches.

Immediately call the Gas Emergency Services on

0800 111 999.

3. Removing the Decorative Front

3.1 Remove the decorative front by lifting to disengage the

fixing hooks from the locating slots, see Diagram 2.

3.2 Place carefully to one side.

3.3 Replace in reverse order.

User Instructions

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gazco Riva 2 F670 Balanced Flue Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info