Bedienungsanleitung Gazco Riva F67 (Seite 15 von 40) (Englisch)

813405

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

3.5 EXTRA FLUE LENGTHS

All flue components are 150mm diameter (6")

NOMINAL

LENGTH ACTUAL

LENGTH STAINLESS

FINISH ANTHRACITE

FINISH

200mm 140mm 8527 8527AN

500mm 440mm 8528 8528AN

1000mm 940mm 8529 8529AN

40° Bend N/A 8507 8507AN

90° Bend N/A 8508 8508AN

NOTE: The following areas need careful consideration:

a) Terminal positions

b) Flue supports

c) Weatherproofing

d) Fire precautions

For all the above options, local and national codes of practice

must be adhered to.

CONVENTIONAL & BALANCED FLUE

4. GAS SUPPLY

4.1 Before installation, ensure that the local distribution

conditions (identification of the type of gas and pressure)

and the adjustment of the appliance are compatible.

4.2 Ensure that the gas supply is capable of delivering the

required amount of gas and is in accordance with the rules

in force.

4.3 Soft copper tubing can be used to install the appliance. Soft

soldered joints can be used externally of the appliance but

must be restricted to the area shown in Diagram 2.

4.4 This appliance is supplied complete with a factory fitted

isolation device incorporated into the inlet connection, no

further isolation device is required.

4.5 All supply gas pipes must be purged of any debris that may

have entered, prior to connection to the appliance.

4.6 The gas supply enters through the silicone panel located on

the RH side of the outer box; this will need to be slit with a

sharp knife prior to passing the supply pipe through.

5. VENTILATION

5.1 This appliance requires no additional ventilation.

INSTALLATION INSTRUCTIONS

SITE REQUIREMENTS - CONVENTIONAL & BALANCED FLUE

6. APPLIANCE LOCATION

6.1 With the exception of the F67 Riva (see below), it is not

necessary to site these products on a non-combustible floor.

However, for practical reasons, the floor should be flat and

solid to allow the appliance to be levelled and secured in

place.

6.2 This appliance may be situated anywhere in the room, but

due consideration should be taken to ensure that it is sited

within the constraints of the allowable flue configuration.

6.3 As well as allowing for the flue position, you must also

consider the position of bench and the F67 upon the

bench.

6.4 If the appliance is to be sited against a combustible wall, a

clearance of 50mm should be allowed between the wall

and the rear of the appliance.

6.5 F67 Riva

The F67 Riva requires a non-combustible hearth.

A non-combustible hearth must be at least 12mm thick and

project 50mm from the base of the stove in all directions.

The minimum dimensions are shown in Diagram 2.

AR0604

MINIMUM CLEARANCE

A = 980 mm

B = 520 mm

C = Minimum 12 mm

6.6 F67 Riva Pedestal & F67 Riva Bench

6.6.1 The Riva Pedestal or the Riva Bench does not need a

non-combustible floor but the appliance must not be

fitted on a carpet. Use a solid floor.

6.6.2 These two appliances can be situated anywhere in the

room but when siting you must consider the constraints

of the flue.

6.6.3 If the appliance is to be sited against a wall, a clearance

of 50mm must be allowed between the wall and the

appliance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gazco Riva F67 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info