Bedienungsanleitung Gazco Riva F67 (Seite 16 von 40) (Englisch)

813405

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

NOTE ON INSTRUCTIONS

The instruction in this document applies to the following

three Riva models:

 • F67RivaPedestal

 • F67RivaBench

 • F67Riva

The instructions vary only where a particular feature of a

specific model requires explanation. Otherwise the

instructions should be understood as applicable to all

three models.

IMPORTANT: ENSURE THAT THE APPLIANCE IS

CORRECTLY ADJUSTED FOR THE GAS TYPE AND

CATEGORY APPLICABLE IN THE COUNTRY OF USE.

REFER TO DATA BADGE AND TECHNICAL

SPECIFICATIONS AT THE FRONT OF THE BOOKLET.

LPG MODELS: THE APPLIANCE IS FACTORY SET TO RUN

ON BUTANE (G30). IF IT IS INTENDED TO BE USED ON

PROPANE (G31) THE AERATION PLATE SUPPLIED MUST

BE FITTED.

TO CHANGE AERATION PLATE REFER TO REPLACING

PARTS, SECTION 8 (BALANCED FLUE) OR 9

(CONVENTIONAL FLUE).

FOR DETAILS OF CHANGING BETWEEN GAS TYPES

REFER TO REPLACING PARTS, SECTION 10 (BALANCED

FLUE) OR 11 (CONVENTIONAL FLUE).

1. SAFETY PRECAUTIONS

1.1 This appliance must be installed in accordance with the

rules in force, and used only in a sufficiently ventilated

space. Please read these instructions before installation and

use of this appliance.

1.2 These instructions must be left intact with the user.

1.3 Do not attempt to burn rubbish on this appliance.

1.4 In your own interest, and those of safety, this appliance

must be installed by competent persons in accordance with

local and national codes of practice. Failure to install the

appliance correctly could lead to prosecution.

1.5 Keep all plastic bags away from young children.

1.6 Do not place any object on or near to the appliance. Allow

adequate clearance above the appliance.

IF THE APPLIANCE IS EXTINGUISHED OR GOES OUT IN

USE, WAIT 3 MINUTES BEFORE ATTEMPTING TO

RELIGHT THE APPLIANCE.

2. INSTALLATION OF THE APPLIANCE

NOTE: THERE IS AN OPTIONAL CONVECTION FAN KIT

AVAILABLE [8566 Balanced Flue or 8571 Conventional

Flue]. THIS CAN BE FITTED EITHER DURING OR AFTER

INSTALLATION, BUT PROVISION FOR A POWER SUPPLY

MUST BE MADE PRIOR TO INSTALLATION OF THE

APPLIANCE.

2.1 Remove the appliance from the carton and discard all

unnecessary packaging. Ensure no components are thrown

away when unpacking.

2.2 Unpack the Spectrum frame supplied with the appliance

and place to one side.

2.3 F67 Riva Bench only

2.3.1 To secure the bench to the floor:

 • Positionthebenchwhererequired

 • Mark its position on the floor through the keyholes in the

small opening on both legs (see Diagram 1).

AR1895

 • Removethebench

 • Drillandfitfixingscrewsinthefloor

 • Partiallytightenprovidingenoughmargintothen:

 • Manoeuvrethebenchandslidethekeyholesintothe 

screws

 • Tightenthescrewsfully

2.3.2 To secure the appliance to the bench you must consider

where you place the appliance on the bench before using

the template (see Diagram 2).

AR1894

INSTALLATION INSTRUCTIONS

INSTALLATION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gazco Riva F67 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info