Bedienungsanleitung Gazco Sheraton 5 - Balanced Flue (Seite 8 von 52) (Englisch)

813479

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

ADVANCED MENU SETTINGS

It is possible to change additional preset settings of the control

features.

Access the Advanced Menu Settings.

Press and release the SET button to enter the Advanced Settings

Menu.

Advanced Settings are:

Back Light (L)

- A = Automatic (default setting).

The backlight comes on in the dark.

- O = Light never comes on.

- 1 = Light comes on when the handset is unlocked.

Display Contrast (C)

- 8 Levels from 0 - 7 (Default level 4).

P = Pairing with devices other than the Control Box.

This feature is not available on this appliance.

IMPORTANT: THE FURTHER FUNCTIONS ON THIS

HANDSET ARE FOR FACTORY SETTING ONLY

AND ARE NOT TO BE USED.

PLACE THE HANDSET ON A FLAT SURFACE AND

WAIT UNTIL THE HOME SCREEN IS DISPLAYED

AND THE UNLOCK LIGHT TURNS OFF.

PAGING THE HANDSET

If the handset is lost it can be located by pressing the + only on the

Control Box for 5 seconds.

The handset will flash and make a noise for 60 seconds to indicate

where it is.

Pick up the Handset and cradle it to unlock. The flashing and noise

will stop.

If the handset is not discovered in 60 seconds the process will

need to be repeated.

CHANGING THE DEFAULT TIMER MODE

It is possible to change the default time period for the Timer mode.

The default time period for Timer mode is factory set to 1

hour.

To change the default time:

Holding the remote to keep the green light on and the handset

unlocked:

Press and hold the SET button until a beep is heard to indicate the

command has been received.

Release the SET button. PROG will be displayed at the top left of

the display.

Repeatedly press the MODE button until the Zzz symbol flashes at

the top of the display.

Press and release the SET button.

Press the + or - buttons to alter the default time period.

The timer can be set between 1 minute and 24 hours.

After adjusting the time press SET again to confirm.

Note: This does not activate the Timer mode, see Installation

Section, Manual Operation or Thermostatic Mode.

REPLACING THE APPLIANCE

BATTERIES

Replace batteries at least every 12 months during the annual

service of the fire.

It is essential to use high quality batteries (Duracell

or equivalent) when replacing batteries.

The icon at the bottom shows the battery condition of both the

batteries in the handset and in the Control Box alternately.

Battery status

RC = Remote Control Handset

FC = Fire Control (Control Box)

Note: Change the batteries in the handset before

they are flat, to avoid having to reprogram the time

of day in again. N.B. Pairing is not lost, even if the

batteries are removed or flat.

The appliance Control Box requires 3 AA size alkaline batteries.

The handset requires 2 AA size alkaline batteries.

Slide the Power Switch on the Control Box to the OFF

( o ) position before attempting to change the batteries.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gazco Sheraton 5 - Balanced Flue Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info