Bedienungsanleitung Gemini 1160RSD (Seite 2 von 3) (Englisch)

479871

Zoom out

Zoom in

Vorherige Seite

1/3

Nächste Seite

GEMINI 1160RSD

Gemini 1160RSD is a remote control unit. Supplied with two coded transmitters it

has the ability to operate central locking, as well as offering panic switch, passive

arming and outlets for control sirens, vehicle's own horns and hazard lights.

It offers the following protections

- the passenger compartment by pin switches and also voltage drop sensor.

- engine immobilisation obtained by the interruption of an electric circuit that

controls the engine.

It has also the following abilities

- it controls all types of sirens or vehicle horns which are positive or negatively

switched.

- it can be connected to volumetric, vibration and anti-lifting sensors.

- it can be interfaced with automatic windows or roof closing units.

OPERATION

: (For End User)

Pushing the BLACK button on the hand held transmitter will switch on the alarm

and operate the central locking.

The receiver is mounted inside the passenger compartment. The arming signal is

acknowledged by a single 3-seconds pulse on the hazard lights circuit.

Pushing the RED button on the hand held transmitter twice will switch the alarm

on with the Remote Sensor Disconnection (for example ultrasonic sensor). In

this case the alarm connection is acknowledged bu two pulses of the direction

indicator lights.

In both cases at the same time the engine immobilisation circuit will be activated.

There are different exit delay periods for each type of activation (see Table A)

before the alarm becomes armed.

After the arming periods have elapsed, any attempt to enter the vehicle will

instantly trigger the alarm. The siren will sound and the hazard lights will also

flash. This will continue for a period of 30 seconds and then the unit will switch off

and automatically re-set after a further 10 seconds. In case of continuous

triggering, the alarm condition will occur as shown in Table A.

The alarm can be de-activated at any time by operating the BLACK button of the

transmitter. The hazard lights will signal 3 off 1 second pulses if no alarm

conditions have occurred. If the alarm has been triggered, the hazard lights will

signal 5 off 1 second pulses (alarm has memory of an atempted "break-in").

If the passive arming has been activated, the alarm unit will arm itself after 15

seconds from the engine stopping and the last door or bonnet/boot/tailgate

closing, also the arming visual signal will operate. To obtain the central locking

closing, you must push the BLACK transmitter button within 20 seconds.

When the system is armed you can activate the panic alarm by

pressing the RED transmitter button. The siren and the hazard lights circuit will be

activated for 10 seconds. The emergency de-activator can be either a key switch

or a toggle switch. If a GEMINI 5025 electronic self-powered siren is used, its key

switch must be turned OFF to obtain the emergency alarm de-activation (it acts as

an over-ride switch).

TABLE A

EXIT DELAY TIME ENTRY SENSOR NO. OF ALARM

CYCLES

40 sec. Door pin switches 3

5 sec. Bonnet/boot/tailgate switches 3

5 sec. Ignition line unlimited

40 sec.

Volumetric, vibration and anti-

lifting sensors

40 sec. Voltage drop sensor unlimited

PRE-INSTALLATION CHECKS

: (For the Installer)

- Disconnect the negative terminal of the battery and only re- connect after the

installation is complete.

- Remove the cover from the rear of the unit, these allow access to the SW2-

SW3. SW1 is located next to the connectors.

Arrange the central unit as follows:

a. SW1 in position A. Voltage drop sensor activated.

SW1 in position B. Voltage drop sensor isolated.

This sensor must be isolated if on the vehicle there are loads that can operate

once the ignition has been switched off (i.e. cooling fan).

b. SW2 in position A o B as shown in central locking diagrams.

c. SW3 in position A. Continous signal.

SW3 in position B. Intermittent signal. For connecting vehicle's own horn select

position B (intermittent signal).

d. To de-activate the passive arming function, cut the YELLOW- GREEN wire

loop.

WIRING INSTRUCTIONS

Check that all wires of the harnesses are fitted in the correct positions on

the connectors (checking against alarm wiring diagrams).

POSITIVE

POWER FEED

With the voltage drop sensor activated, the

RED wire must be connected to the interior light circuit at the fuse box.

If the voltage sensing is de-activated, the RED wire

CAN

be connected

to the main fuse box feed or directly to the positive terminal of the

battery. If a self-powered electronic siren (GEMINI 5025) is used the

RED wire of the remote unit must be connected to the RED wire of the

siren.

DO NOT CONNECT THE RED WIRE OF THE SIREN TO

POSITIVE.

Use the 15 Amp fuse supplied in the kit.

NEGATIVE POWER FEED.

Connect the BROWN wire to a stable body

earth. If possible use existing body earth points or battery negative

terminal.

IGNITION LIVE.

Connect the YELLOW wire to a positive ignition feed.

This wire

must be fed also whilst starting the engine

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gemini 1160RSD Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info