Bedienungsanleitung Gemini 7201 (Seite 2 von 9) (Englisch)

479852

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

DESCRIPTION

The system Gemini 7201 is a compact alarm supplied with sensors and siren, which can be

installed on vehicles with 12Volt battery-negative to earth.

FUNCTIONS

GEMINI 7201.

- Compact alarm with dynamic code (Frequency 433.92 MHz ).

- Blinker and electronic siren.

- Negative control for supplementary siren.

- Electrical central door locking control (negative or positive) windows and electric sunroof (for

vehicles equipped with Pack-comfort system).

- Perimetric and volumetric protection (US and HF models).

- LED’s memory and wiring connections diagnosis.

- Remote controlled PANIC function.

He alarm systems are equipped with 2 codified transmitters (art. 7208E).

INSTALLATION INSTRUCTIONS (for the installer)

- To make universal the central door locking system it is necessary to use a 5056 module.

- Connect the power feed wire to the battery positive terminal and the earth directly to the

vehicle frame.

- Connect the alarm Green-Brown wire to the door pin-switch.

- Avoid routing connection wires next to interference sources (sparking plugs cables, high

voltage coil).

- The alarm must be installed in the engine compartment protected from water and with the

key lock switch turned to the top.

- If you install an ultrasonic module the ultrasonic heads must be positioned at the top of each

windscreen pillar and must be pointing at each opposite diagonal corner away from the facia

outlets.

DIP-SWITCHES PROGRAMMING TABLE

1 ON Current absorption sensor ON

1 OFF Current absorption sensor OFF

2 ON Closure control 6 seconds

2 OFF Closure control 1 second

3 ON Comfort control ON (25 seconds)

3 OFF Comfort control OFF

4 ON Diagnostics ON

4 OFF Diagnostics OFF (normal use)

5 ON

5 OFF

Do not use

6 ON Self-learning of a new active code

6 OFF Self-learning of a new excluded code (normal use)

ATTENTION : SET THE DIP-SWITCHES BEFORE TURNING THE EMERGENCY KEY TO ON.

FOLLOWING THE PRESENT RULES IT IS ADVISABLE TO SET THE DIP-SWITCH N. 1 TO OFF.

DIAGNOSTICS: (final check-up o f the installer or quick after sale checks).

The diagnostics function allows during the test or at the end of the installation to verify quickly the

correct working of the alarm system and the electrical connections of the vehicle plant.

DIAGNOSTICS INLET. With the emergency key to OFF, set the dip-switch N.4 to ON. The activation

of the diagnostics function is signalled by 4 acoustic/optical signalling while supplying the alarm

system. At the end of the signalling the module outlets (+A) and the engine immobilisation

activates; the LED lights fix.

In this condition it is possible to test each inlet and if the external connections and/or the internal

circuits of the device work correctly one audible tone or one-direction indicator lights flashing signal

each alarm triggering.

It is necessary to wait 1 second between each alarm input triggering. In the diagnostics modality

the transmitter 1 button does not work as arming/disarming button but it is used to verify the

transmitter’s working. An audible tone or one direction indicator lights flashing signals the correct

working.

The transmitter 2 button activates the Panic alarm. This modality allows testing the siren working

and the outlet of the additional siren with negative control.

To stop the Panic alarm it is necessary to press again on the button 2 of the transmitter (followed

by a neutral period of 5 seconds).

DIAGNOSTICS OUTLET.

1. Press on the transmitter 2 button to activate the panic function.

2. During the alarm signalling, pressing on the transmitter 1 button the system goes back to the

normal working.

ATTENTION! AT THE DIAGNOSTIC OUTLET SET THE DIP-SWITCH N.4 TO OFF.

WIRING CONNECTIONS

(disconnect the negative pole of the battery and only reconnect after the installation is complete)

FUNCTION WIRE COLOUR

Earth ðð BLACK initialled “M”

Battery positive ðð BLACK initialled “R”

Ignition live ðð YELLOW

Direction indicator lights ðð 2 x ORANGE

Door pin switch ðð GREEN-BROWN

Boot and bonnet switch ðð GREEN

Positive alarm armed ðð PINK

Sensors inlet ðð GREEN-BLACK

Outlet negative control for

additional siren

ðð YELLOW-BLACK

Central door locking ðð YELLOW-RED, YELLOW-GREY, RED-GREY

NOTE: in the wiring harness there are 2 connectors; connect the 4-pin connector to the

ultrasonic module and the 2 -pin connector to the LED.

WORKING DESCRIPTION

ALARM ARMING

Press on the transmitter 1 button. The arming is signalled by 1 direction indicator lights flashing

and one acoustic signal (can be excluded).

ALARM DISARMING

Press on the transmitter 1 button. The disarming is signalled by 3 direction indicator lights flashing

and 3 acoustic signalling (can be excluded); 5 direction indicator lights flashing and 5 audible tones

(can be excluded) if an alarm condition has occurred.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gemini 7201 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info