Bedienungsanleitung Gemini 7350 (Seite 2 von 10) (Englisch)

479857

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

INTRODUCTION

GEMINI 7350.

The system 7350 is a self-powered compact alarm unit that includes sensors and siren. It's suitable to be

fitted on vehicles equipped with 12 Volts battery (negative ground).

DESCRIPTION

- Remote controlled compact alarm unit with self-powered electronic siren and dynamic code transmission

(433.92MHz).

- Direction lights outputs.

- Additional siren negative output.

- Universal central door locking control, electric windows and sunroof control on vehicles equipped with

"Comfort Closing System".

- Doors, boot and bonnet protection.

- External sensors input (Volumetric protection).

- Engine immobilisation (Not available for Belgium model - V.V.3 rules).

- Alarm passive arming with casual re-arming feature and "GARAGE" position.

- LED alarms memory.

- Arming vehicle check.

- Diagnostic Mode feature (for the installer).

- Remote controlled "PANIC" alarm / "ELECTRIC BOOT" release. (Selectable).

The alarm system is equipped with two codified remote transmitter and two codified electronic keys.

FITTING INSTRUCTIONS (reserved to the installer).

- The alarm unit must be installed in the bonnet in vertical position, with the connectors turned upwards, in a

place far from heat sources, water ingress, ignition control unit and coils.

- Be sure that the alarm wiring harness is far from high-tension wires of the original vehicle plant in order to

avoid interference which could generate a wrong functioning.

- On vehicles equipped with catalytic muffler the engine immobilisation must be carried out on fuel pump.

- If the alarm system is equipped with a ultrasonic module (ref. 5123), the ultrasonic cells must be fitted at

the top of each windscreen pillar, far from the ventilation or air-conditioning outputs and pointed at each

opposite diagonal corner.

- Connect the positive power supply of the alarm unit to the positive pole of the vehicle battery and connect

the negative power supply of the alarm unit to the negative pole of the battery or to the vehicle frame.

- IMPORTANT : In order to obtain the properly working of the passive arming / door protection it's

mandatory to connect the GREEN-BROWN wire to the door pin switches.

DIP SWITCHES PROGRAMMING TABLE

1 ON Panic alarm ON / Boot release OFF

1 OFF Panic alarm OFF / Boot release ON

2 ON Central Door Locking Pulse 6"

2 OFF Central Door Locking Pulse 0,5"

3 ON Central Door Locking Comfort Pulse ON ( 25" )

3 OFF Central Door Locking Comfort Pulse OFF

4 ON Alarm Passive Arming ( with casual re-arming ) ON *

4 OFF Alarm Passive Arming OFF *

5 ON Diagnostic Mode ON

5 OFF Diagnostic Mode OFF ( Normal Mode )

6 ON Remote Controls / Electronic Keys self-learning ON

6 OFF Remote Controls / Electronic Keys self-learning OFF ( Normal Mode )

IMPORTANT : THE DIP-SWITCHES MUST BE SELECTED BEFORE TO CONNECT THE POWER

SUPPLY TO THE ALARM UNIT. ( SEE ALSO "DIP-SWITCHES RE-SETTING" CHAPTER).

* For the Belgium market unit it's no possible to switch OFF the Alarm Passive Arming feature ( V.V.3 Rules ).

DIP-SWITCHES RE-SETTING.

It's possible to change the dip-switch settings, after the power supply connection , by the following instructions :

1. Disarm the alarm unit by a remote control / electronic key.

2. Set the dip-switches in order to program the features required.

3. Turn the ignition switch to ON position ( without start the vehicle engine !! ).

4. Insert , for more than 3 seconds, an electronic key in the LED / Socket . To confirm the new dip-switch settings a LED

flash /audible tone will be emitted.

5. Turn the ignition switch to OFF position.

DIAGNOSTIC MODE ( final check for the installer or quick check during after sale service ).

This feature allows to the installer / service personnel to quickly verify the correct working of the alarm unit and the

electrical connections to the vehicle plant.

DIAGNOSTIC SET-ON.

To enter in the Diagnostic Mode it's possible to follow two different ways :

1. During the installation of the alarm system : Set on the dip-switch no. 5 before to connect the power supply of the alarm

unit and then connect the power supply.

2. For post-installation services : Set on the dip-switch no. 5 following the instructions described in the "DIP-SWITCHES

RE-SETTING" chapter.

To confirm the diagnostic mode will be emitted four indicator lights flashes / audible tones. At the end of the signalling the

LED and the external module output ( +A / PINK wire) will be switched on.

In this condition it's possible to test each alarm input, and if the external connection and/or the internal alarm unit circuit

works properly an audible tone / indicator lights flash will be emitted each time the input of the alarm system will be

triggered. It's important to have a delay time of 1 second ( or more ) between each alarm input triggering.

In the diagnostic mode it's possible to verify the right working / transmission range of the remote controls by pressing the

push button no.1 of the handsets. If the device works properly an audible tone / indicator lights flash will be emitted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gemini 7350 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info