Bedienungsanleitung Gemini 7350 (Seite 3 von 10) (Englisch)

479857

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

By the push button no.2 of the remote controls it's possible to activate the PANIC alarm. In this condition it's possible to

test the internal siren circuit and the negative output for an external additional siren. It's possible to halt the PANIC alarm

by pressing the remote control push button no.2 again ( in this case there will be a neutral time of five seconds ).

DIAGNOSTIC SET-OFF.

To set-off the Diagnostic Mode and to enter in the Normal Mode it's possible to follow two different ways :

1. Insert an electronic key in the LED / Socket. To confirm the normal mode will be emitted three indicator lights flashes /

audible tones.

2. Press the button no.2 of the remote control to activate the PANIC alarm, then press the button no.1 of the remote

control in order to set- off the diagnostic mode.

IMPORTANT : At the end of the diagnostic mode the Dip-Switch no.5 must be set in OFF position !!

WIRING CONNECTIONS ( Disconnect the negative pole of the battery before the installation ).

FUNCTION WIRE COLOUR

Earth ( Negative pole of the battery )

⇒

BLACK marked “M”

Positive pole of the battery

⇒

BLACK marked “R”

Engine immobilisation

⇒

2 x BLACK marked “H”

Starting Key

⇒

BLACK marked “G”

Direction Indicator lights

⇒

2 x ORANGE

Door pin switch

⇒

GREEN-BROWN

Boot / Bonnet pin switches

⇒

BLACK marked “V”

Positive output - alarm armed

⇒

PINK

External sensors input

⇒

GREEN-BLACK

Electrical Boot release output - ( negative )

⇒

BLACK marked "HN"

External siren negative output

⇒

BLACK marked "GN"

Central Door Locking

⇒

YELLOW-BLUE, RED-BLUE, YELLOW-GREY,

RED-GREY, YELLOW-BROWN, RED-BROWN

VERY IMPORTANT!!

• ALL WIRING IDENTIFICATION MUST BE REMOVED DURING THE INSTALLATION.

• ALL POINTS OF CONNECTION SHOULD BE SOLDER ED AND INSULATED WITH HEAT SHRINKABLE TUBING, OR

USING ONLY THE ORIGINAL CONNECTORS AND PLUGS HOMOLOGATED BY THE MANUFACTURER .

• FOR PREVENT ACCIDENTAL DISCONNECTION , ALL THE WIRES, THE ELECTRONIC KEY CONNECTORS AND

CODE BUS CONNECTOR MUST BE FITTED BY SOME PLASTIC CLAMPS ON THE ORIGINAL CAR HARNESS.

OPERATING INSTRUCTIONS ( installer ).

ALARM ARMING - BY REMOTE CONTROL.

Press the push button no.1 of the remote control. The arming of the alarm system is signalled by one direction lights pulse

/ audible tone ∗.

The central door locking will be closed with the pulse programmed during the installation.

ALARM DISARMING - BY REMOTE CONTROL.

Press the push button no.1 of the remote control. The disarming of the alarm system is signalled by three direction lights

pulses / audible tones ∗. If an alarm condition occurs during the arming period the direction lights pulses / audible tones ∗

will be five instead of three ( see also " LED ALARM MEMORY" chapter ). The central door locking will be opened with

the pulse programmed during the installation.

ALARM ARMING / DISARMING - BY ELECTRONIC KEY.

It's possible to use the electronic keys to arm and disarm the alarm system. In this case the central door locking are not

powered and a entry delay time of 10 seconds is provided in order to disarm the system without false alarms.

∗ In order to override the audible tone see the "AUDIBLE TONES SETTING" chapter.

SPECIAL FUNCTIONS.

PANIC ALARM.

If the dip-switch no.1 is set in ON position, it's possible to obtain a PANIC ALARM by pressing the push button no.2 of the

remote control.

The length of the panic alarm period is 29 seconds, but it's possible to halt this alarm by pressing again the push button

no.2 of the remote control. The panic alarm is available with the alarm system disarmed, or armed after the neutral time of

45 seconds.

ELECTRIC BOOT RELEASE.

If the dip-switch no.1 is set in OFF position, it's possible to use the push button no.2 of the remote control to open the

electrical lock of the boot on vehicles equipped with this feature. The electric boot release is available with the alarm

system disarmed or armed. If the alarm system is armed a delay time of 60 seconds is provided in order to open the boot

without false alarms, during this time period the LED is lighted in fix mode.

EXTERNAL SENSOR INPUT / ALARM ARMED POSITIVE OUTPUT OVERRIDE.

During the first 25 seconds of the neutral arming period it's possible to override the external sensor input and the positive

output ( +A / PINK wire ) in order to halt the window raise. This feature is obtained by pressing the push button no.2 of the

remote control and it's signalled by a direction lights pulse; on vehicles equipped with the "Comfort Closing System" - (

dip-switch no. 3 in ON position ) the external sensor override feature halts the central door locking pulse in order to stop

the window raise.

To exclude the external sensor input with the window totally closed it's necessary to wait the total closure and then press

the push-button no. 2 of the remote control.

AUDIBLE TONES SETTING.

This alarm system allows to the user to switch ON / switch OFF the audible tones by the remote control.

AUDIBLE TONE SWITCH OFF.

1. Turn the ignition key in ON position ( without start the vehicle engine !! ).

2. Press the push-button no.1 of the remote control for more than 3 seconds. To confirm the audible tones switch

OFF a LED flash will be emitted.

3. Turn the ignition key in OFF position.

Gemini 7350 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info