Bedienungsanleitung Gemini 7502 (Seite 5 von 13) (Englisch)

479839

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

ACCESSORY FUNCTIONS

MEMORY OF LAST ALARM TRIGGERED:

Indications regarding the last alarm condition detected (ALARM MEMORY) are provided by the

status LED as visual signals which differ as a function of the cause that has triggered the alarm. If

any alarms have occurred, this signal emitted when the vehicle engine is started (positive pole under

key in the ON position), after the alarm system has been turned off.

The visual signal is repeated five times and there is a 2” pause between the emission cycles. The

visual signal can be cut off by turning the ignition key to the OFF position.

LED SIGNALS REFLECTING ORIGIN OF ALARM

CONDITION

CAUSE OF ALARM

ß ˜ ß

Power drain sensor

ß ß ˜ ß ß

Positive pole under key

ß ß ß ˜ ß ß ß

Door pushbuttons

ß ß ß ß ˜ ß ß ß ß

Wires cut

ß ß ß ß ß ˜ ß ß ß ß ß

Pushbuttons for bonnet, boot and external sensors

ß ß ß ß ß ß ˜ ß ß ß ß ß ß

External radio sensor

l LED OFF (2 seconds) Y LED ON ( 400mS)

Besides the accessory functions previously described (see “CUTTING OUT THE EXTERNAL SENSORS/

STOPPING WINDOW UPWARD TRAVEL / COMFORT”; “CUTTING OUT THE SIREN” and “MEMORY

OF LAST ALARM TRIGGERED”) the following accessory functions are available and can be programmed

and used by the user or installer:

a) PANIC ALARM

b) ACTIVATION OF ANTI-DISTRACTION / AUTOMATIC DOOR-LOCKING FUNCTIONS

c) DOUBLE PULSE FOR CENTRALIZED UNLOCKING OF DOORS

d) PASSIVE ACTIVATION OF ENGINE IMMOBILIZER FUNCTION

e) GARAGE FUNCTION

PANIC ALARM / CAR FINDER

If enabled, the PANIC ALARM function allows the user to activate the visual and audio alarm signals

deliberately by pressing key 2 on the remote.

This function works regardless of whether the alarm system is ON or OFF. The alarm signal lasts up

to approx. 30”. However, you can silence it at any time by pressing key 2 on the remote again.

Between one PANIC ALARM cycle and the next there is a neutral time of approximately 5” during

which it is not possible to activate the alarm signal again.

While the alarm signal is emitted and during the consequent neutral time, the LED stays on.

IF DURING THE PROGRAMMING PHASE, THE PANIC FUNCTION HAS BEEN DISABLED, THE CAR FINDER

FUNCTION WILL BE ACTIVATED.

The CAR FINDER function allows, with the ALARM ACTIVATED, you to obtain a short visual/audio

signal by pressing key 2 on the remote. This function can be useful to look for the car in a parking lot

or multi-storey garage without creating useless sound pollution.

The brief visual/audio signal consists of a low beep and the simultaneous flashing of the turn

indicators (total length of indication is one second).

NOTE: the emission of the audio signals is subordinate to their being enabled when programming

the accessory functions.

ACTIVATING THE ANTI-DISTRACTION / AUTOMATIC DOOR-LOCKING FUNCTION.

When this function is enabled, it causes the automatic activation of the alarm system if the latter has

been turned off and no voluntary actions are performed by the user (e.g. OPENING A DOOR OR

STARTING THE CAR) within approx. 35”.

The function prevents the vehicle from being left unprotected in cases where, after the activation of

the protection system, key 1 on the remote is pressed accidentally and the alarm system is turned

off by mistake.

The automatic activation of the alarm is evidenced by the regular visual signals described above.

The anti-distraction function activates the centralized door-locking control. Therefore, in

order to prevent involuntary activations of the alarm system, it is INDISPENSABLE to connect

the driver’s side door pushbutton to the alarm system input.

In conjunction with the ACTIVATION OF THE ANTI-DISTRACTION function, the AUTOMATIC

DOOR-LOCKING function is also enabled.

This function allows the automatic management of the centralized locks according to the running

status of the vehicle.

The doors will lock automatically 20” after the engine is started (positive pole under key in the ON

position).

The doors will unlock automatically 1” after the engine is turned off (positive pole under key in the

OFF position).

Locking and unlocking times are programmed during the installation of the alarm system. To prevent

this function from being activated accidentally, the system continuously monitors the status of the

ignition key and the input line of the DOOR AND BOOT PUSHBUTTONS and therefore does not

allow operation of the locks if the DOORS and BOOT are opened manually while starting the engine

or during the 20” after starting it.

DOUBLE PULSE FOR CENTRALIZED DOOR-UNLOCKING FUNCTION

By enabling this function you will obtain, upon the deactivation of the alarm system, a double control

pulse on the door-unlocking line, each pulse lasting 0.5”. This allows the release of the centralized

door locks on cars having the Dead-Lock function, which requires this type of signal.

The function, which can be enabled by programming during installation, is active only if the

opening/closing time of 0.5” is selected.

Selecting an opening/closing time of 6” automatically excludes the double pulse upon opening.

PASSIVE ACTIVATION OF ENGINE IMMOBILIZERS

If enabled, this function automatically activates the double ENGINE IMMOBILIZER function approx.

45” after the engine is turned off. (Automatic activation of the alarm is indicated by the usual

audio/visual signals already described in this document).

Activation of the PASSIVE ALARM ACTIVATION procedure is signaled, when the vehicle engine is

turned off, by the flashing of the turn indicators for approximately one second, overlapped by two

flashes of the LED and the simultaneous emission of two high beeps.

During the time between the activation of the PASSIVE ALARM ACTIVATION and the actual

activation of the protection system, it is possible to temporarily interrupt the activation procedure by

opening the DRIVER’S SIDE DOOR. This allows the user to operate calmly in the vehicle without

activating the alarm system.

This pause mode is indicated by the LED emitting continuous light, and turning off when the vehicle

door is closed, thus indicating the continuation of the activation count.

NOTE: audio signals will be emitted only if they have been enabled when programming the

accessory functions.

GARAGE FUNCTION.

This function lets you suspend the ANTI-DISTRACTION AND PASSIVE ACTIVATION function. It

can be useful for the purpose of facilitating maintenance and/or car washing operations without

having to give the remotes or the electronic keys of the alarm system to the car mechanics.

To activate the GARAGE function, it is indispensable to enable the ANTI-DISTRACTION AND

PASSIVE ACTIVATION functions.

Follow this procedure:

1) With the alarm system deactivated, turn the ignition key to the ON position. The status LED will

turn on for approximately 0.5”.

Gemini 7502 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info