Bedienungsanleitung Gemini 7590 (Seite 3 von 12) (Englisch)

479861

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

INTRODUCTION

GEMINI 7590.

The 7590 system is a alarm control unit with built-in sensors and can be installed on cars having a 12-

volt battery with the negative pole earthed.

DESCRIPTION

- Alarm control unit, remote-controlled with a dynamic code.

- Blinker and universal control to operate the centralised door locks, electric windows and roof (for

cars equipped with the “pack-comfort” system).

- Boundary and volume protection.

- Controls for self-powered siren and supplementary siren (continuous or intermitted sound).

- LED memory.

- Remote “panic” and/or boot opening function.

- Two electrical engine immobilisation.

- Electronic emergency key with dynamic code (CDE2).

- Control unit functions programmable by means of remote control.

The alarm control unit is equipped with two dual-channel remotes (7208E) working at a frequency of

433.92 MHz, and two electronic keys (CDE2).

INSTALLATION TIPS

- Connect the positive and negative power cables of the alarm system to the battery or to one of its

branch wires.

- Always connect the Green-Brown alarm lead to the door pushbutton.

- On cars with catalytic converters, implement the electrical engine blocks by working on the fuel pump

and the starter motor.

- Do not lay connection cables near sources of interference.

- Position the ultrasound capsules on the RH and LH pillars of the front windshield. Aim them at the

car interior, at some distance from the air vents.

ELECTRIC CONNECTIONS

(REMOVE THE NEGATIVE POLE OF THE BATTERY AND RECONNECT IT ONLY AFTER ASSEMBLY IS COMPLETED)

FUNCTION WIRE COLOUR

Earth

BLACK marked with M

Positive pole of battery

BLACK marked with R

Engine immobilisation 1 (max.8A)

TWO, BLACK marked with H

Engine immobilisation 2 (max.8A)

TWO, BLACK marked with B

Positive pole under key

YELLOW

Turn indicators

TWO, ORANGE

Door and boot pushbuttons

GREEN-BROWN

Bonnet pushbutton

BLACK marked with V

Positive pole of alarm activated (max. 700 mA)

PINK

External sensors input

GREEN-BLACK

Control for self-powered siren

BLUE

Negative control for supplementary siren or

horn

YELLOW-BLACK

Negative output for electrically-operated boot

opening function

GREY-BLACK

Centralised locks

YELLOW-BLUE, RED-BLUE,

YELLOW-GREY, RED-GREY,

YELLOW-BROWN, RED-BROWN

NOTE : In the wiring harness of the 7590 there are two 2-way connectors that must be

connected to the electronic key socket (art. 2390 or art. 2325). If only the LED (art.

2324) is used, use only the 2-way connector with the Red wire and the Black wire.

ACCESSORY FUNCTIONS PROGRAMMABLE BY REMOTE.

FUNCTION FACTORY PROGRAMMING

Continuous or intermittent sound Continuous sound enabled

Centralized lock times (0.5 / 6 sec.) selection 0.5 seconds

25-second command to close comfort function Disabled

Double pulse when opening Disabled

Power drained Disabled

Anti-distraction – automatic door-locking function

Disabled

Passive activation of engine blocks Disabled

Panic function / Boot opening function Panic function enabled

ENTERING THE PROC EDURE FOR PROGRAMMING THE ACCESSORY FUNCTIONS.

Disconnect the alarm with the transmitter. Open the car door (and keep it open). Turn the ignition key

to the ON position: the LED will turn on for 0.5 seconds. When the LED is on, press both keys on the

remote. To confirm activation of programming mode, the LED and turn indicators will flash rapidly

twice. The system is now in the programming mode and therefore it is awaiting commands that must

be imparted by means of the remote control keys.

CHANGING FUNCTION STATUS.

Each selection will be confirmed by a LED signal:

IF YOU PRESS PUSH BUTTON 1 (DOTTED) THE LED WILL GIVE OUT ONE LIGHT SIGNAL AND GO ON TO THE

NEXT FUNCTION .

IF YOU PRESS PUSH BUTTON 2 (SMOOTH) THE LED WILL GIVE OUT TWO LIGHT SIGNALS AND GO ON TO

THE NEXT FUNCTION .

PUSH BUTTON 1 : Intermittent sound (horn)

CONTINUOUS / INTERMITTENT SOUND

PUSH BUTTON 2 : Continuous sound

PUSH BUTTON 1 : Time enabled 6 seconds

CENTRALIZED LOCK TIMES

PUSH BUTTON 2 : Time enabled 0.5 seconds

PUSH BUTTON 1 : Enabled

COMFORT CONTROL

PUSH BUTTON 2 : Disabled

PUSH BUTTON 1 : Enabled

DOUBLE PULSE UPON OPENING

PUSH BUTTON 2 : Disabled

PUSH BUTTON 1 : Enabled

POWER DRAINED

PUSH BUTTON 2 : Disabled

PUSH BUTTON 1 : Enabled ANTI-DISTRACTION –

AUTOMATIC DOOR-LOCKING FUNCTION

PUSH BUTTON 2 : Disabled

PUSH BUTTON 1 : Enabled

PASSIVE ACTIVATION OF ENGINE BLOCKS

PUSH BUTTON 2 : Disabled

PUSH BUTTON 1 : Panic function enabled

PANIC / BOOT OPENING FUNCTION

PUSH BUTTON 2 : Boot opening function enabled

NOTE : AUTOMATIC ACTIVATION OF ENGINE IMMOBILISATION FUNCTION AND BOOT OPENING FUNCTION BY

MEANS OF THE REMOTE (ON PREDISPOSED VEHICLES) IS ENABLED AT THE FACTORY AND CANNOT BE

CHANGED IN THE VERSI ON FOR THE DUTCH MARKET (NL).

EXITING ACCESSORY FUNCTION PROGRAMMING PROCEDURE.

You can exit the programming procedure at any time by turning the ignition key to the OFF position. At

this point, the changes made will be memorized and the previous status of the functions that have not

been changed will be confirmed.

However, if the procedure is carried on for all the functions on the table, when the last function (Panic

or Boot opening) has been programmed, the system will indicate the end of accessory function

programming by emitting two rapid flashes of the LED and the turn indicators.

Gemini 7590 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info