Bedienungsanleitung Gemini 863 (Seite 7 von 8) (Englisch)

479884

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

PAGE 12 - INSTALLER MANUAL INSTALLER MANUAL - PAGE 13

11.0 - ADDING NEW DEVICES 12.0 - DELETING PROGRAMMED DEVICES

To carry out the operation successfully, make sure the required electrical connections

(door push-button, bonnet push-button and positive under key) are complete.

To carry out the operation successfully, make sure the required electrical connections

(door push-button, bonnet push-button and positive under key) are complete.

All device previously programmed in the memory, such as control devices, magnetic contacts,

opening detectors or infrared sensors, can be erased

To clear memory proceed as follows

With system disarmed, open the driver side door and the bonnet and leave them open!

Turn ignition key “ON-OFF”-“ON-OFF”-“ON-OFF”-“ON”.

At the fourth rotation, leave it “ON”.

Close the bonnet; ithe LED will be steady “ON”.

To confirm it has entered in the delete mode, the system gives two acoustic signals (one high and

one low-pitched)

Keep the bonnet closed (approx. 8 sec.) until the devices are completely deleted

The following operations must be carried out within four seconds otherwise the

procedure is invalidated.

”.

The end of the procedure is indicated by the LED turnings OFF and one long low-pitched acoustic

signal

Turn ignition key “OFF

50 devices.

Storing memory is for

If an extra device is added, it automatically deletes the first device programmed in the

system memory

To activate the procedure proceed as follows:

With system disarmed, open the driver side door and the bonnet and leave them open! .

Turn ignition key “ON-OFF”-“ON-OFF”-“ON-OFF”-“ON”.

At the fourth rotation, leave it “ON”.

To confirm it has entered in the self-learning mode of new control devices, magnetic contacts,

opening detectors or infrared sensors the system gives two acoustic signals (one high and one low-

pitched)

The following operations must be carried out within four seconds otherwise the

procedure is invalidated.

Do not close the bonnet otherwise all previously programmed devices are erased as

described in the next paragraph.

The system is ready to receive the device codes.

the button nr.1 of the remote,

“OFF”.

According to the device to be stored in memory, press insert the

electronic key into the receptacle, make the magnetic contact transmit (bring contact and magnet

close together and then move apart), press the push-button on the opening detector or make the

infrared sensor transmit (see sensor instructions)

Each time a device is learned a high-pitched signal sounds and the status LED flash briefly

epeat this procedure to program other devices

Turn ignition key

o confirm the end of the procedure a low-pitched signal sounds

If the bonnet is opened before 8 seconds, the devices will not be

deleted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gemini 863 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gemini 863

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info