Bedienungsanleitung Gemini 933 (Seite 6 von 9) (Englisch)

479887

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

9.0 - VEHICLE CODE PROGRAMMING

”.

f the system is to be managed via CAN-BUS line, it must be configured according to the vehicle on

which it is to be installed.

To help you understand the coding procedure, here below is an example illustrating the configuration

procedure.

In this case the code used is 1-0-3 which hypothetically corresponds to a “FIAT XXXXX

e area).

A separate leaflet, included in the alarm packaging, lists all the available vehicles

(codes are updated at packaging time).

Up-to-date information on supported vehicle models can be found at: www.gemini-

alarm.com (privat

Press the vehicle remote control lock/unlock buttons to make sure the alarm system works

properly.

Eventually disconnect the 8-way connector and reconnect it after few seconds

TEN FLASHES AND

A SHORT PAUSE

THREE FLASHES

ONE FLASH AND A

SHORT PAUSE

Connect the connectors of the wiring harness to the connector of the system.

.Press and hold the button shown below until the LED lights up

Release the button, the LED switches off.

After a 3/4 seconds pause, the LED starts the first sequence of flashes.

Press “1”.the button at the first flash which corresponds to number

After a 4 seconds, the LED starts the second sequence of flashes.

Press “0”.the button at the tenth flash which corresponds to number

After another 4 seconds, the LED starts the third sequence of flashes.

Push the button at third LED flashing, corresponding to value “3”.

When the last digit is entered, the alarm system “repeats” the entered code.

10.0 - SELF-LEARNING OF TURN INDICATORS FLASHES

In order to arm/disarm through the turn indicators, the system must learn the vehicle locking (arming)

and unlocking (disarming) flashes.

Connect the WHITE-ORANGE wire to the turn indicators and proceed as follows

Disconnect the 8-way wiring connector from the 8-way system connector.

Turn ignition key “ON”.

Connect the 8-way wiring connector to the 8-way system connector; the LED turns on steady.

urn ignition key

lose all doors and press the lock button on the original remote control.

When the turn indicators stop flashing, a high-pitched acoustic signal confirms the learning of the

arming flashes.

Press the unlock button on the original remote control.

When the turn indicators stop flashing, 2 high-pitched audio signals confirm the learning of the

disarming flashes.

This completes the procedure

T “OFF”.

To cancel the programming of the turn indicators reset the system (see

chapter 16.0).

Press

FIRST

FLASH

TENTH

FLASH

THIRD

FLASH

3-4 seconds

PAGE 10 - INSTALLER MANUAL INSTALLER MANUAL - PAGE 11

The system has an indicator LED that signals any wrong vehicle code inserted.

The code must be range between 100 and 235 otherwise the LED on the unit blinks

repeatedly and the procedure is interrupted.

The previously inserted code remains stored.

The procedure is also invalidated if the LED blinks more than 10 times.

In this case there are no optical warnings, the procedure is simply be interrupted.

In either case, repeat the whole procedure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gemini 933 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gemini 933

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info