Bedienungsanleitung Gemini 933 (Seite 7 von 9) (Englisch)

479887

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

11.0 - SYSTEM PROGRAMMING

The t

able below applies to the system programmed in “standard configuration”.

very time you enter the programming procedure, the alarm resets to the default settings.

FUNCTION STATUS LED FLASHES

Disabled

Enabled

Disabled

Enabled

Disabled

-----

Exclusion of arming/disarming optic signalling

Exclusion of arming/disarming acoustic signalling

System passive arming

Arming of self-powered coded siren

Doors input - positive

Optical pulse signalling

Negative output during alarm cycle

For Gemini only, turn ignition key

PAGE 12 - INSTALLER MANUAL INSTALLER MANUAL - PAGE 13

11.7 -

NEGATIVE OUTPUT SELECTION (DURING ALARM) FOR HORNS OR ADDITIONAL

SIREN

Once activated, this function can activate the output for the siren (continuous tone) or for the horn

(intermittent tone

If the function is disabled, under normal operating conditions, the blue wire carries a negative signal;

during an alarm cycle, there is a lack of negative.

12.0 - SYSTEM PROGRAMMING EXAMPLE

Here below is an example that illustrates the various steps to follow to modify the programmable

functions.

As mentioned before, every key rotation disables a function, while the electronic key enables it.

When ignition is turned On or Off or the electronic key is touched to its receptacle, a high or low pitched

signal sounds and the LED flashes according to table in chapter 11.0

In both cases, system moves on to the next function.

signals

Repeat steps above to enable or disable other functions.

When the last function is programmed (either with the electronic key or the ignition key), in

addition to the confirmation tone, the system gives two low-pitched and one high-pitched acoustic

and the turn indicators flash twice.

These last two signals indicate the end of the programming procedure.

With alarm system disarmed, turn ignition key “ON” and touch electronic key to

its receptacle.

Two acoustic signals (a high and a low-pitched sound) and two flashes of the turn indicators

indicate that the system is in the programming procedure.

OFF-ON

Boop

Beep

Turn ignition “OFF” and then back “ON” to

disable the function.

A low-pitched acoustic signal confirms the

operation.

The LED flashes according to selected function

(from 1 to 8).

Touch electronic key once to its receptacle to

activate the function.

A high-pitched acoustic signal confirms the

operation.

The LED flashes according to function the

selected function (from 1 to 8).

When the optical pulse signaling feature is activated, the blinkers will ONLY emit optical

signals during an alarm cycle.

The system BLUE wire MUST be connected to the Hazard push-button.

In this case, do not connect the ORANGE wires (see chapter 7.3)

Alack of power during electrical system maintenance, will not affect the programming.

The procedure must be carried out entirely because key rotation disables the selected function and

moves to the next one until the programming procedure is completed.

Programmable functions are briefly described below and the next paragraph illustrates the

programming instructions.

This function activates optic signals during system arming (1) and disarming (2).

11.1 - OPTICAL SIGNALS

If the vehicle already has optical locking/unlocking signals, the turn indicators alarm

flashes should be deactivated.

11.2 - ACOUSTIC SIGNALS

11.3 - PASSIVE ARMING

11.4 - ENABL

11.5 - DOOR SWITCH POLARITY SELECTION

11.6 - OPTICAL PULSE SIGNAL/SELF-POWERED SIREN

This function activates acoustic signals during system arming (1) and disarming (2).

(art. 7725).

This function modifies the alarm input signal (positive or negative) according to the signal generated

This function activates the optical

This function arms the system 60” after ignition is switched off and the last door is opened and closed.

If a door is opened during this lapse of time, the procedure is interrupted and it is resumed when the

door is closed

by the doors switch.

signals according to the connection made; only for vehicles where

hook-up is to the “emergency” push-button wire (Hazard push-button)

ING OF SIREN (7725) OUTPUT

This function enables the relative output (20-way connector, position 13, PINK wire) to activate the

self-powered coded siren

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gemini 933 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gemini 933

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info