Bedienungsanleitung Gerlach GL 7923 (Seite 6 von 128) (Alle Sprachen)

797687

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

C. Temperature / timer down button

D. Temperature / timer up button

E. Sleep mode button

F. Fan speed selection button

G. Timer button

H. Air oscillation button

CONTROL PANEL manual operation – picture D

When the is powered on for the first time, the buzzer will shout, and then the device will get into standby status.

Press button “A” to turn on and turn off the device, the buzzer will play signal once.

MODE SELECTION on manual operation of control panel –

When the device is power on, choose mode you need between cooling mode or fan mode or dehumidifying mode as below:

Cooling mode -

- Press button “J” to select cooling mode, next press the button “L” to get slow fan speed button or press the button “M” to get fast fan

speed button. Next press button “ C” or “ D” to adjust required temperature from 16℃ to 31℃, buttons are not available in fan or

dehumidifying mode.

Fan mode -

- Press button “F” to select fan mode, the LCD screen will show “FA”, next press the button “L” to get slow fan speed button or press the

button “M” to get fast fan speed button. During fan mode operation the temperature and sleeping functions cannot be setup.

Dehumidifying mode –

- Press button “K” to select dehumidifying mode, the LCD screen will show “dh”. Under dehumidifying mode, sleep mode cannot be setup,

and fan speed is fixed on slow fan speed automatically and cannot be changed. In order to switch off the dehumidifying mode select other

operation mode: cooling or fan mode.

Timer set up -

- When the device is not working, press button “G”, the LCD screen flashes, press the button “C” or “D” to set up the quantity of hours after

the device will start to operate. The LCD screen stops flashing and timer icon will be illuminated.

- When the device is working, press button “G”, the LCD screen flashes, press the button “C” or “D” to set up the quantity of hours need to

pass before the device will shut off automatically. The LCD screen stops flashing, the timer icon will be illuminated, LCD screen shows

required to achieve temperature. This is a delayed start function.

Timer operation range can be fixed by each one hour from 1 to 24 hours.

Sleep mode –

- At first Press button “J” to cooling mode, next press button “E” to turn on the sleep mode, then the device will work on Energy-Saving and

quiet type.

- Next press button “ C” or “ D” to adjust required temperature from 16℃ to 31℃.

- The sleep mode is automatically programmed. After the first hour of operation, the temperature will increase by 1 ℃, after the second hour

of operation, the temperature will increase by another 1 ℃, and then remain at the same level.

- Press button “E” again to cancel sleep mode.

NOTE: Sleep mode is not available in dehumidify and fan modes.

Water full -

The water full indicator lamp “N” will be illuminated and the buzzer will alarm for several second, then the compressor will stop to work when

the inner device water tank will be full.

Automatic air oscillation function –

Press an air oscillation button (H), after the device turns on, automatic air oscillation function turns on, the louver will swing continuously

the left and the right; by pressing the button again the movement will stop and the louver remain in that position.

The radius of horizontal air oscillation is 30 degrees left and 30 degrees right direction from the middle vertical.

REMOTE CONTROLLER operation – picture E

The remote controller transmits signals to the system.

Button "A" - the device will be started when it is energized or will be stopped, if you press this button again.

Button "B" - press it to select operation mode: cool mode → dry mode → fan mode.

Button "C" / "D" - press to set up the operation time from 1 to 24 hours or required room temperature from 15 to 31°C when cooling mode is

switched on.

Button "E" - press it to set up or cancel sleep mode.

Button "F" - press it to select fan speed in sequence: slow / fast wind speed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gerlach GL 7923 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info