Bedienungsanleitung Gerlach GL 7923 (Seite 7 von 128) (Alle Sprachen)

797687

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

Button "G" - press it to set up or cancel timer.

Button “H” - press to set up or cancel automatic air oscillation function.

PROTECTION DEVICES

1.Compressor protection: Three minutes later after power on / restart, compressor starts to run.

2.Overflow protection function: when the water full indicator lamp “N” will be illuminated and the buzzer will alarm for several second, the

device turn off automatically. In this case, you need to drainage the water (details see Drainage Instructions at the end of this chapter). After

the water is emptied, the device will get into standby status.

3. Frost Protection Function: In cooling mode, if the temperature of the EVA pipe sensor is too low, the device will automatically enter

protection status. When the temperature of the EVA pipe sensor rises to a certain temperature, it can automatically revert to normal

operation.

DRAINAGE INSTRUCTIONS:

This device is equipped in auto-water-evaporating system. Condensed water cycle will cool down the condenser, which will not only

improve cooling efficiency, but also save energy.

1. If inner water tank is full, the water full indicator lamp “N” will be illuminated, the device enter into standby mode, buzzer shouts,

compressor stops and all buttons is invalid till the device recovers to be normal, after water drainage.

2. Power off the device.

3. Prepare flat container (not included to set) to drain the water. Locate it under the drain hole (8)

3. Remove the rubber cap from the drain hole (8) – picture F.

4. During drainage, the body can be tilted slightly backwards.

5. After water stops to pouring out, close the rubber cap (8).

6. Restart the device, the device will runs normally.

CLEANING & MAINTENANCE

Cleaning: before cleaning and maintenance, turn off the device and unplug the plug.

a) Housing cleaning

Clean with surface of device with a wet soft cloth. Don't use chemicals, such as benzene, alcohol, gasoline, otherwise, the surface of the

device will be damaged or even the whole device will be damaged.

b) Net nylon filters cleaning

If nylon filter (12) is clogged with dust, then the effectiveness of the device is reduced, be sure to clean the filter once every two weeks.

- Force down from the outside the latch of filter frame (11) with hands and pull out to yourself to remove the filter frame(11).

- Clean the upper and down filters frame (11) after remove both nylon filters (12) from the filter frame(11). – picture G.

- Put nylon filter (11) into warm water with neutral detergent (about 40℃ / 104℉) and dry it in the shade after rinsing clean.

STORAGE

If the device will be unused for a long time, please do as following :

1.Pull out drainage plug (8) to flow out water.

2.Let the device runs under fan mode for 2 hours to dry out the device's internal.

3.Turn off the device and pull out plug .

4.Clean and dry filters, then reinstall them.

5.Pull out exhaust pipe for safe keeping .

6.Put the device into plastic bag , and place it on a dry place.

7.Remove batteries of the remote control and keep them properly.

Storage the device and all device components in dry place.

TROUBLESHOOTING

Problem I.: The air conditioning does not work.

Reason 1:There is no electricity. So, turn it on after connecting it to a socket with electricity.

Reason 2: The water full indicator light “N” is illuminated. So, discharge the water.

Problem II.: The device auto-restarts frequently.

Reason1: Direct sunlight. So, drawn the curtains.

Reason 2: Door and windows are open , many heat sources in the room. So, close the door and windows, move out heat sources.

Reason 3: Filters are too dirty. So, clean or replace filters.

Reason 4: Air-inlet or air out-let is blocked. So, remove blockage.

Problem III.: Big Noise

Reason: The device is not placed on a flat surface. So, put the device on a flat and hard place to reduce noise.

Problem IV.: Compressor does not work.

Reason: Compressor time-delay protection turn on. So, wait for 3 minutes until the temperature is lowered, and then restart the device.

Note: when abnormal situations are occurred, turn off device and pull out plug, then contact with professional service for help .

Do not repair the device yourself. Not qualified repair will void the warranty.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gerlach GL 7923 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info