Bedienungsanleitung Gloria Multibrush li-on (Seite 31 von 99) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch)

725139

Zoom out

Zoom in

Vorherige Seite

1/99

Nächste Seite

the motor/gear unit (L), as illustrated.

Release the spring-loaded lock (K),

the drive arm is locked when the

locking device independently returns

to its original position .

NOTE!

If the drive unit (P) cannot be pushed

onto the drive shaft, reach under the

safety guard (O) and turn the hexago-

nal drive until the drive unit (P) slides

onto the drive shaft easily and without

force.

Put the surface brush (N) onto the

hexagonal drive and then the guide

arm (M), as illustrated, on the steering

side of the motor/gear unit (L).

Now slide the lock (K) into open posi-

tion , hold this and press the guide

arm (M) further onto the coupling shaft

up to the stop. Release the spring-load-

ed locking device (K). The guide arm

(M) is locked when the locking device

independently returns to its original

position .

NOTE!

Whilst assembling the surface brush,

make sure that the side part of the

safety guard on guide arm (M) is firmly

connected to the safety guard and is

correctly sealed.

7.1.4 Using the surface brush on

rough surface structures e.g. tiles,

paving slabs, exposed aggregate

concrete, stoneware etc.

Figure 21

Place the switched-on device parallel

on the surface to be treated. Hold the

device at working angle and make sure

that the rubber lip on the safety guard

is just above the ground. Walk at an

even steady pace and push the device

in front of you. Depending on the

degree of soiling, apply light to medi-

um pressure on the surface brush,

adapt your pace of work to the degree

of soiling.

NOTE!



Always work parallel and hold the

device away from your body.



When working close to edges, the

narrower side of the device should

point towards the wall.



In cases of stubborn dirt you can move

the device backwards and forwards on

the spot (like a scrubber), until the

required result is achieved.



Moist cleaning is also possible in cases

of heavy soiling. Use a sprayer to moist

the surface to be cleaned with water or

a cleaning agent, a GLORIA sprayer is

ideal for this purpose. After moit clean-

ing rinse the surface with water.

CAUTION

RISK OF INJURY FROM RUNNING

BRUSHING TOOL!



Never lift the device off the ground

whilst switched on during work as

there is danger of entanglement!

7.1.5 Using the surface brush

on wood surfaces (optionally

available as an accessory)

ATTENTION

Improper use of the device poses a risk

of damage to property! You should

therefore observe the following safety

instructions:



Never use the hard surface brush

with the black bristles for cleaning

wood surfaces, as the hard bristles

attack the surface of the wood,

thereby damaging it.

RZ_MULTIBRUSH_Li-on__DE/GB/FR/NL/IT/DK_979162.qxp_Text_GB 04.03.20 17:01 Seite 32

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gloria Multibrush li-on Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info