Bedienungsanleitung Gloria Multibrush li-on (Seite 32 von 99) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch)

725139

Zoom out

Zoom in

Vorherige Seite

1/99

Nächste Seite

NOTE!



For cleaning wood surfaces use the

soft surface brush with the yellow /

black bristles. This is available as a

GLORIA accessory and is not in cluded

in the scope of delivery.



Assembly and operating instructions

can be found in the product informa-

tion “Surface brush for wood

surfaces”.

7.1.6 Using and replacing the

joint brush

Figures 22 - 24

Assemble the joint brush as described

in Chapter 7.1.3. Place the device

parallel with guiding wheel and joint

brush on the joint to be treated. Hold

the device at working angle and make

sure that the rubber lip on the safety

guard (H) is just above the ground.

NOTE!

To adjust the safety guard (H), turn the

7 click-stop safety guard to the posi-

tion described under point “21”.

Align the joint brush with the centre of

the joint, walk at an even steady pace

and push the device in front of you.

Adapt your pace of work to the degree of

soiling.

NOTE!



Always work along the joint and hold

the device away from your body.



In cases of stubborn dirt you can move

the device backwards and forwards on

the spot (like a scrubber), until the

required result is achieved.

CAUTION

RISK OF INJURY FROM RUNNING

BRUSHING TOOL!



Never lift the device off the ground

whilst switched on during work as

there is danger of entanglement!

7.2 User information



Do not remove any wet weeds with the

device.



Never clean wood decks or wood

terraces with the joint brush.



Only clean joints that are intact.

Damaged or crumbling joints or joints

with cracks should not be cleaned with

the device.



Rinse the cleaned surfaces thoroughly

after cleaning.



Worn brushes i.e. frayed wire bristles

should be replaced in good time.

To prevent damaging the device, it is

essential that the joint brush is replaced

when the diameter is < 90mm.

7.3 Replacing the joint brush

Figures 25 - 29



Switch off the device and remove the

battery (C).

Open the locking device (K) of the

joint brush unit (J), as shown in the

illustration, and remove the joint

brush unit.

Unscrew the hexagon socket screw

3-4 turns so far out of the joint brush

housing, until safety guard (H) can eas-

ily be twisted and pulled off.

Now press lock button (Q) which blocks

the drive shaft and unscrew the

hexagon socket screw, which fixes the

joint brush (J), from the drive shaft ( ).

Remove the disc from the joint brush.

ATTENTION

Improper use of the device poses a risk

of damage to property! You should

therefore observe the following safety

instruction:



Never activate the lock button (Q)

when the joint brush is running.

Pull the joint brush (J) from the flange

on the shaft and exchange it for a new

one.

Assembly is carried out in reverse order

( ).

RZ_MULTIBRUSH_Li-on__DE/GB/FR/NL/IT/DK_979162.qxp_Text_GB 04.03.20 17:01 Seite 33

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gloria Multibrush li-on Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info