Bedienungsanleitung Godox Speedlite TT350 Canon (Seite 9 von 13) (Englisch)

708921

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

- 22 -

Setting <Multi>

1 stroboscopic flash.

● Long press the <MODE>

button for 2 seconds so that

<Multi> is displayed. Long

press the <MODE> button

for 2 seconds again to exit.

7. M: Wireless Flash Shooting with Manual Flash

This describes wireless (multiple shooting) using manual flash. You

can shoot with a different flash output setting for each slave unit

(firing group). Set all parameters on the master unit.

Setting the flash mode to

1 <M>

● Press the <MODE> Button

to set the flash to M mode.

Setting flash output

● Turn the Select Dial to set

the flash output of the

groups.

Taking the picture

● Each group fires at the set

flash ratio.

Using a flash (master/slave) with a radio transmission wireless

shooting function make it easy to shoot with advanced wireless

multiple flash lighting, in the same way as TTL autoflash shooting.

The basic relative position and operation range are as shown in the

picture. You can then perform wireless TTL autoflash shooting just

by setting the master unit to <TTL>.

8. Multi: Wireless Flash Shooting with Manual

Flash

Setting flash output/flash

2 frequency/flash times.

● Setting the flash

output/flash frequency/flash

times in the A group. Setting

the multi flash mode. (see

Page35 )

● B and C group can only

control the ON/OFF of the

slave unit by pressing the

<MODE> Button.

Transmission distance is about 30m.

● Use the supplied mini stand to position the slave unit.

● Before shooting, perform a test flash and test shooting.

● The transmission distance might be shorter depending on the

conditions such as positioning of slave units, the surrounding

environment and whether conditions.

You can divide the slave units into two or three groups and perform

TTL autoflash while changing the flash ratio (factor). In addition, you

can set and shoot with a different flash mode for each firing group,

for up to 3 groups.

Wireless Multiple Flash Shooting

● Auto Shooting with Two Slave Groups

Slave/Master Unit's Positioning and Operation Range

● Autoflash Shooting with One Slave Unit

● Auto Shooting with Three Slave Groups

- 39 -

- 40 -

MODE ZOOM SYNC SLAVE

SET

MODE ZOOM SYNC SLAVE

SET

MODE ZOOM SYNC SLAVE

SET

1. Disturbed by the 2.4G signal in outer environment (e.g. wireless base

station, 2.4G wifi router, Bluetooth, etc.)

　 → To adjust the channel CH setting on the flash trigger (add 10+ channels) and

　 use the channel which is not disturbed. Or turn off the other 2.4G equipment

　 in working.

2. Please make sure that whether the flash has finished its recycle or caught up

with the continuous shooting speed or not(the flash ready indicator is lighten)

and the flash is not under the state of over-heat protection or other abnormal

situation.

→Please downgrade the flash power output. If the flash is in TTL mode, please

　 try to change it to M mode(a preflash is needed in TTL mode).

The Reason & Solution of Not Triggering in Godox 2.4G Wireless

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Godox Speedlite TT350 Canon Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info