Bedienungsanleitung Godox Speedlite V860II Canon (Seite 8 von 23) (Englisch)

708926

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

● If the subject is too far away and underexposure, the < >

icon will blink in the viewfinder. Move closer to the subject

and try the FE lock again.

● If <ETTL> is not displayed on the LCD panel, FE lock

cannot be set.

● If the subject is too small, FE lock might not be very

effective.

● If you set a shutter speed that is the same as or slower than

the camera’s maximum flash sync speed, < > will not be

displayed in the viewfinder.

● With high-speed sync, the faster the shutter speed, the

shorter the effective flash range.

● To return to normal flash, press < > button again. Then

< > will disappear.

● Multi flash mode cannot be set in high-speed sync mode.

● Over-temperature protection may be activated after 15

consecutive high-speed sync flashes.

High-Speed Sync

High Speed Sync (FP flash) enables the flash to synchronize with all

camera shutter speeds. This is convenient when you want to use

aperture priority for fill-flash portraits.

Second-Curtain Sync

With a slow shutter speed, you can create a light train following the

subject. The flash fires right before the shutter closes.

Press function button 4 < >

button so that < > is displayed

on the LCD panel.

Press Function Button 2

1 < > so that < > is

displayed.

Check that < > is

2 displayed in the viewfinder.

SYNC

The flash output is adjustable from 1/1 full power to 1/128th power

in 1/3rd stop increments. To obtain a correct flash exposure, use a

hand-held flash meter to determine the required flash output.

M: Manual Flash

Press < MODE > button so

1 that < M > is displayed.

Turn the Select Dial to choose

2 a desired flash output amount.

Press < SET > button again to

3 confirm the setting.

Figures displayed when reducing flash output level→

←Figures displayed when increasing flash output level

1/41/21/1

1/1-0.3

1/2+0.7

1/1-0.7

1/2+0.3

1/2-0.3

1/4+0.7

1/2-0.7

1/4+0.3

······

Flash Output Range

The following table makes it easier to see how the stop changes in

terms of f/stop when you increase or decrease the flash output. For

example, when you decrease the flash output to 1/2, 1/2-0.3, or 1/2-

0.7, and then increase the flash output to more than 1/2, 1/2+0.3,

1/2+0.7, and 1/1 will be displayed.

Optic S1 Secondary Unit Setting

In M manual flash mode, press <S1/S2> button so that this flash can

function as an optic S1 secondary flash with optic sensor. With this

function, the flash will fire synchronously when the main flash fires,

the same effect as that by the use of radio triggers. This helps create

multiple lighting effects.

Optic S2 Secondary Unit Setting

Press <S1/S2> button so that this flash can also function as an optic

S2 secondary flash with optic sensor in M manual flash mode. This

is useful when cameras have pre-flash function. With this function,

the flash will ignore a single “preflash” from the main flash and will

only fire in response to the second, actual flash from the main unit.

● S1 and S2 optic triggering is only available in M manual

flash mode.

- 53 -

- 54 -

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Godox Speedlite V860II Canon Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info