Bedienungsanleitung Godox Speedlite V860II Canon (Seite 10 von 23) (Englisch)

708926

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

Positioning and Operation Range (Example of wireless flash

shooting)

● Autoflash Shooting with One Slave Unit

● Use the supplied mini stand to position the slave unit.

● Before shooting, perform a test flash and test shooting.

● The transmission distance might be shorter depending on

the conditions such as positioning of slave units, the

surrounding environment and whether conditions.

Transmission distance is about 100m.

● Auto Shooting with Two Slave Groups

● Auto Shooting with Three Slave Groups

You can divide the slave units into two or three groups and perform

E-TTL II autoflash while changing the flash ratio (factor). In addition,

you can set and shoot with a different flash mode for each firing

group, for up to 5 groups.

Wireless Multiple Flash Shooting

Wireless shooting using radio transmission has advantages over

wireless shooting using optic transmission, such as being less affected

by obstacles, and not having to point the slave unit’s wireless sensor

toward the master unit. The main functional differences are as follows:

Function

Distance

Channel

A/B/C Power

To be Disturbed

Group

Radio Transmission

100m

1~32

OFF, 1/128~1/1

Hard

A/B/C/D/E

Optic Transmission

15m

1~4

1/128~1/1

Easy

A/B/C

● There are four flash modes in this wireless radio transmission:

TTL, M, Multi and Gr. Choose one of those modes by pressing

the MODE Button.

- 57 -

- 58 -

Ceiling

Manualflash

Autoexternal

flashmetering

E-TTL II

* The flash mode settings are indicated only as an example

● Shooting with a Different Flash Mode set for Each Group

Manualflash

The Reason & Solution of Not Triggering in Godox 2.4G Wireless

1. Disturbed by the 2.4G signal in outer environment (e.g. wireless

base station, 2.4G wifi router, Bluetooth, etc.)

　 → To adjust the channel CH setting on the flash trigger (add 10+

channels) and use the channel which is not disturbed. Or turn off the

other 2.4G equipment in working.

2. Please make sure that whether the flash has finished its recycle

or caught up with the continuous shooting speed or not(the flash

ready indicator is lighten) and the flash is not under the state of

over-heat protection or other abnormal situation.

　 →Please downgrade the flash power output. If the flash is in TTL

　mode, please try to change it to M mode(a preflash is needed in TTL

　mode).

3. Whether the distance between the flash trigger and the flash is

too close or not

　 →Please turn on the “close distance wireless mode” on the flash

trigger (＜0.5m):

　X1 series: press the test button and hold on, then turning it on until

　the flash ready indicator blinks for 2 times.

　XPro series: Set the C.Fn-DIST to 0-30m.

4. Whether the flash trigger and the receiver end equipment are in

　the low battery states or not

　 →Please replace the battery(the flash trigger is recommended to use

　 1.5V disposable alkaline battery).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Godox Speedlite V860II Canon Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info