Bedienungsanleitung Godox V350N (Seite 9 von 14) (Englisch)

683875

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

MODE ZOOM SYNC SLAVE

SET

MODE ZOOM SYNC SLAVE

SET

MODE ZOOM SYNC SLAVE

SET

MODE ZOOM SYNC SLAVE

SET

MODE ZOOM SYNC SLAVE

SET

MODE ZOOM SYNC SLAVE

SET

Long Press the <SYNC>

1 button for 2 seconds so that

< > is blinking. Turn the

Select Dial until the < > is

displayed on the LCD panel,

which means the slave unit.

Slave Unit Setting

Press the <SLAVE> Button to

1 ch o ose t h e gro u p fro m

M/A/B/C. Then, press the

< MODE > Button so that the

master unit can work in OFF /

TTL / M flash mode. Choose

one of them as the flash

mode of master unit.

3. Setting the Communication Channel

If there are other wireless flash systems nearby, you can change the

channel IDs to prevent signal interference. The channel IDs of the

master unit and the slave unit(s) must be set to the same.

Long press the <SLAVE>

1 Button for 2 seconds until the

channel IDs is blinking. Turn

the Select Dial to choose a

channel ID from 1 to 16.

Press the <SET> button to

2 confirm.

2. Setting Master Unit’s Flash Mode

Press the <MODE> Button for

2 2 seconds to switch to Multi

mode.

Slave Unit Setting

● Set the V350N that to be

controlled as the wireless

slave unit. (Page 41)

● The slave unit can be set

as A/B/C.

Check the communication

3 channel

● If the master unit and

slave unit(s) are set to a

different channel, set them

to the same channel.

(Page 41)

Position the camera and

4 flashes

● Position the camera and

flashes as the picture

shows. (Page 43)

Check the flash operation

● Press the master unit’s

Test Button< >.

● Then, the slave unit will

fire. If not, adjust the slave

unit’s angle toward the

master unit and distance

from the master unit.

The slave unit might be out of order or fire an unwanted flash

due to the nearby wifi routers or other 2.4G equipments. If in

this case, please adjust the flash’s channel or turn off the 2.4G

equipments.

Autoflash Shooting with One Slave Unit

5. TTL: Fully Automatic Wireless Flash Shooting

Master Unit Setting

● Attach a V350N camera

flash on the camera and set it

as the master unit. (Page 40)

● M/A/B/C can be set as

TTL mode independently.

- 41 -

- 42 -

4. Wireless ID Settings

Change the wireless channels and wireless ID to avoid interference

for it can only be triggered after the wireless IDs and channels of the

master unit and the slave unit are set to the same.

Press the <MENU> button to enter C.Fn ID. Press the <SET> button

to choose OFF channel expansion shutdown, and choose any figure

from 01 to 99.

6. M: Wireless Flash Shooting with Manual Flash

This describes wireless (multiple shooting) using manual flash. You

can shoot with a different flash output setting for each slave unit

(firing group). Set all parameters on the master unit.

Setting the flash mode to

1 <M>

● Press the <MODE> Button

to set the flash to M mode.

Setting flash output

● Turn the Select Dial to set

the flash output of the

groups.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Godox V350N Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info