Bedienungsanleitung Gorenje b 9010 al (Seite 4 von 17) (Englisch)

330554

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

Instructions for use, installation and connection

Oven illumination

• When the oven is on, the lamp is also on, regardless of the

operation mode.

• If the oven is off, touch the sensor (1) and select the symbol

"Light" (1), then touch the light ON/OFF sensor (5) turn the

lamp on. Next touch of the ON/OFF sensor turns the lamp

off.

Selection and setting of oven temperature

After selecting the type of food and oven function mode, by

pressing the sensors (3a/3b) you may select the desired oven

temperature in the range from 30 – 250°C (depending upon the

selected operation mode) in 5°C intervals.

During the operation, oven temperature may

be randomly increased or decreased within

the permitted temperature range (see chart)

by pressing the sensors (3a/3b).

Table of data for operation mode (with a sensor 2)

Operation mode

Preset

temperature (°C)

200 160 200 170 250 160 160 150 -

Preset time

(h/min)

---------

Possibillity of max.

set temperature (°C)

250 250 250 250 250 220 220 200 -

Oven thermostat signal lamp (d3-2)

• Signal lamp is on; oven temparture is below the setting and

the oven is heating.

• Signal lamp is off; the temperature in the oven has reached

the set temperature.

• Signal lamp is flashing regularly; the oven is set to the end of

operation mode with the adequate sensor (d4-2); the

preparation of food has not started as yet (the appliance

automatically computes the relevant moment of starting the

oven operation).

Setting the operation time

• The time of oven operation may be selected in the range

from 0 to 6 hours, in 1 minute intervals.

• After selecting the function mode and the temperature, by

pressing the sensor 4 you may now select the operation time

from 0 to 6 hours, in 1 minute intervals.

• Touch the selection sensor (4), the display

(d4-1) starts flashing. By touching sensors (4a/4b) set the

desired operation time.

• Turn the oven on with the ON/OFF sensor (5).

• When the set time has elapsed, the oven is switched off

(signalled by the beep, oven operation time symbol (d4-1)

and the relevant signal lamp (5a) are flashing).

• By touching any sensor (except the ON/OFF sensor (5),

which turns the sound signal off and switches the oven on)

you may switch the sound signal off, otherwise it is turned off

automatically after 7 minutes.

Oven operation time may be changed during

the operation.

Setting the end of operation time

• This function is used when you wish to select the end of

operation (cooked food) at exactly the pre-selected time.

• The function may be used only with previously set time of

operation ((d4-1) is on).

• By touching the selection sensor (4) symbol (d4-2) flashes,

and the display (d4-6) flashes the sum of daily current time

and the oven operation time. Use the sensor (4a) to set the

desired end of oven operation.

• Switch the oven on with the ON/OFF sensor (5). The

appliance awaits the start of operation (oven thermostat

signal lamp symbol flashes regularly (d3-2), oven operation

time symbol is on (d4-1) and end of operation time symbol

(d4-2) is also on.

• The starting time is now defined automatically. At the

moment the oven starts the operation, the end of operation

symbol (d4-2) goes off, oven illumination is on, and the oven

thermostat signal lamp (d3-2) is on until the set temperature

is reached.

• Eventual immediate start of operation may be provoked by

simultaneous pressing of sensors (4a/4b) (for approximately

5 seconds).

Alarm timer

This function may be applied separately, and is not in

connection with the oven operation. It is use whenever you

wish to be warned at a pre-selected time.

• By touching the selection sensor (4) provoke flashing of the

alarm timer symbol (d4-4) (the display (d4-6) flashes

"»00:00«). Set the desired time with sensors (4a/4b) in the

range from 0 to 99 minutes in 1 minute intervals. The

countdown starts after approximately 5 seconds, the alarm

timer symbol (d4-4) is on, the display (d4-6) indicates the

current time.

• By touching the selection sensor (4) you may check and

correct the remaining time, indicated on the display (d4-6).

• By simultaneous pressing of sensors (4a/4b) (approximately

5 seconds) the remaining time may also be set to »00:00«.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gorenje b 9010 al Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info