Bedienungsanleitung Gossen Metrawatt METRISO 1000A (Seite 5 von 10) (Englisch)

590651

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

GMC-I Messtechnik GmbH 5

4 Measuring Direct and Alternating Voltage

Direct voltages and sinusoidal alternating voltages with frequencies

ranging from 40 to 200 Hz can be measured with this instrument. Needle

deflection is always positive for direct voltage measurements regardless of

polarity at the terminal connections. Alternating voltage is displayed as an

RMS value.

➭ Set the function selector switch to the “1000 V” position.

➭ Make certain that the needle points to the “0” mark at the V scale in

the idle state. Readjust the needle if necessary with the adjusting

screw for mechanical zero adjustment.

➭ Rotary switch position is irrelevant for voltage measurement.

➭ Probe the measuring point with both test probes.

➭ Read the measurement value from the V scale.

Notes

• Allowable overload capacity for the voltage measuring range is

1200 V.

• Input impedance for the voltage measuring range is 0.9 MΩ.

• Devices under test with capacitive charges are automatically

discharged by the test instrument. The corresponding drop in voltage

can be observed at the display.

5 Measuring Insulation Resistance

Before performing measurement, make certain that the device under test

is voltage-free (see chapter 4).

5.1 Measurement Procedure

➭ First set the function selector switch to the R1 position.

➭ Briefly short circuit the test probes and press the measurement key to

check for full-scale deflection for R1 = 0 MΩ (zero adjustment).

The needle must point to the above indicated full-scale deflection

mark in the idle state. Readjust the needle if necessary with the rotary

knob for electrical zero adjustment.

➭ Depending upon the nominal voltage of the device under test, select a

test voltage of either 50 V, 100 V, 250 V, 500 V or 1000 V with the

rotary switch.

Note

Full-scale deflection must be tested in the following cases, and must be

readjusted if required in order to attain a measuring accuracy of 1.5%:

• Each time a different nominal voltage is selected

• For resistance measurements of long duration

➭ Probe the measuring point with both test probes.

➭ Press the measurement key and read the measurement value from

the appropriate scale.

➭ If needle deflection is insufficient, switch to the next highest

measuring range, i.e. R2 or R3, with the function selector switch.

➭ Multiply the displayed value by the conversion factor which appears

opposite the selected nominal voltage:

Attention!

Do not touch the conductive ends of the two test probes after the

instrument has been activated for the measurement of insulation

resistance.

If measurement is being performed at a purely ohmic device

under test, current may flow over your body, which, although it

does not reach life endangering levels, causes a clearly

discernible shock.

When measurements are made at capacitive devices under test,

e.g. cables, the DUT may be charged with voltages of up to

approximately 1200 V, depending upon selected nominal voltage.

Contact with the device under test after measurement is, in this

case, life endangering!

For this reason, the DUT must be discharged in a controlled

fashion as described in chapter 4 on page 5.

Nominal Voltage: 50 V 100 V 250 V 500 V 1000 V

Conversion

Factor:

x 0.1 x 0.2 x 0.5 x 1 x 2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gossen Metrawatt METRISO 1000A Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info