776259
17
Zoom out
Zoom in
Vorherige Seite
1/62
Nächste Seite
GMC-I Messtechnik GmbH 17
6.2 3-Phase Measurement (line-to-line voltage) and Phase
Sequence
Connection
The measuring adapter
(2-pole) is required in
order to connect the
instrument, and is
expanded to a 3-pole
measuring adapter with
the included measure-
ment cable.
Press softkey U3~.
A clockwise phase
sequence is required at all 3-phase electrical outlets.
Measurement instrument connection is usually problematic
with CEE outlets due to contact problems.
Measurements can be executed quickly and reliably without
contact problems with the help of the Z500A variable plug
adapter set available from GMC.
Connection for 3-wire measurement: L1-L2-L3 at plug in
clockwise direction as of PE socket
Direction of rotation is indicated by means of the following dis-
plays:
Note
See section 16 regarding all indications for the mains
connection test.
Voltage polarity
If the installation of single-pole switches to the neutral conductor
is prohibited by the standards, voltage polarity must be tested in
order to assure that all existing single-pole switches are installed
to the phase conductors.
7 Testing RCDs
Testing of residual current devices (RCDs) includes:
Visual inspection
•Testing
Measurement
Use the test instrument for testing and measurement.
Measuring Method
The following must be substantiated by generating a fault current
downstream from the RCD:
That the RCD is tripped no later than upon reaching
its nominal fault current value
That continuously allowable touch voltage value
UL agreed upon for the respective system is not exceeded
This is achieved by means of:
Touch voltage measurement,
10 measurements with full-waves and extrapolation of IΔN
Substantiation of tripping within 400 ms or 200 ms with IΔN
Substantiation of tripping current with rising residual current
This value must be between 50% and 100% of IΔN (usually
about 70%).
No premature tripping with the test instrument, because test-
ing is begun with 30% residual current (if no bias current
occurs within the system)
Clockwise Counterclockwise
RCD/FI
Table
Differential
Current Waveform
Correct RCD/RCCB Function
Type AC Type A/F
Type B/B+ Type EV/MI
Alternating
current
Suddenly occurring
✔✔✔
Slowly rising
Pulsating
direct current
Suddenly occurring
✔✔
Slowly rising
Direct
current ✔✔
Direct
current
up to 6 mA
IΔN
3
--------
IΔN (measurement for up to 1000 ms)
ta
Ia
t
17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Gossen Metrawatt Profitest Intro wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info