Bedienungsanleitung Gossen Metrawatt SECULIFE ST HV (Seite 42 von 72) (Englisch)

590775

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

42 GMC-I Messtechnik GmbH

15.5 Testing Devices in Accordance with DIN VDE 0701, part 240

You can either change over to testing in accordance with the new

VDE 0701-0702 standard or perform the following measurements in ac-

cordance with the above-mentioned standard:

Testing safety class I and II data processing equipment and office machines as

individual devices and in combination with one another.

The following measurements can be performed in accordance with the

above mentioned standard:

• Protective conductor R

(permanent connection or with plug)

Test current: DC ±200 mA

• Contact current I

• According to DIN VDE 0701, part 240, the device protective conduc-

tor must be tested after maintenance, repair or modification of data

processing equipment and office machines, and exposed, conductive

parts must be tested for the absence of voltage. This applies to:

• Safety class I devices for all exposed, conductive parts which are accessi-

ble to the user, and which are not connected to the protective conductor

• Safety class II devices (totally insulated devices) for all exposed,

conductive parts which are accessible to the user

with the mains plug poled in both directions.

Setting Up the Test Sequence

See chapter 15.4 regarding the test sequence.

Special Parameters

Combined Testing

Safety class I and II devices can be tested individually or in

combination. All protective conductor connections are tested

first for interconnected safety class I devices, and then – as is

also the case for interconnected safety class II devices – all

exposed, conductive parts.

Connecting the Device Under Test

õ Connect the test instrument and the DUT as described below:

– Connect both devices to separate mains outlets.

The outlets to which the test instrument and the safety class I DUT

are connected must share a common protective conductor!

– Or connect the test instrument to the mains and the DUT to the test

socket at the test instrument.

Data Processing / Office Machines

Permanently connected or with plug

To test socket at the instrument

The requirement for testing with the mains

plug poled in both directions can be fulfilled

by connecting the DUT to the test

socket at the instrument, and by activat-

ing mains polarity reversal in the setup

menu under “Sequence”. Each time the

key (14) is activated, phase conductor L

and neutral conductor N are reversed at

the test socket.

Attention!

Testing with mains polarity reversal or with the mains plug poled

in both directions results in interruption of supply power to the

affected data processing equipment or office machine. This test

may thus only be conducted with the consent of the operator of

the data processing equipment or office machine.

If the DUT is defective, the electrical system’s RCCB may be

tripped during testing which would also result in interruption of

supply power to the affected equipment or office machine.

The manufacturer of the test instrument assumes no liability for

the loss of data or other damage which result from use of the

test instrument.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gossen Metrawatt SECULIFE ST HV Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info