470665
32
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
Grandstream Networks, Inc. GXP User Manual Page 32 of 44
Firmware 1.2.5.3 Last Updated: 03/2011
Voice Frames per TX
This field contains the number of voice frames to be transmitted in a single
Ethernet packet (be advise
d the IS limit is based on the maximum size of
Ethernet packet is 1500 byte (or 120kbps)).
When setting this value, be aware of the requested packet time (ptime, used in
SDP message) is a result of configuring this parameter. This parameter is
associated with the first
codec in the above codec Preference List or the actual
used payload type negotiated between the 2 conversation parties at run time.
E.g.
, if the first codec is configured as G.723 and the “Voice Frames per TX” is
set to 2, then the “ptime”
value in the SDP message of an INVITE request will
be 60ms because each G.723 voice frame contains 30ms of audio. Simi
larly, if
this field is set to 2 and the first codec is G.729 or G.711 or G.726, then the
“ptime” value in the SDP message of an INVITE request will be 20ms
.
If the configured voice frames per TX exceeds the maximum allowed value, the
IP phone will use and save the maximum allowed value for the corresponding
first codec choice. The maximum value for PCM is 10 (x10ms) frames; for
G.726, it i
s 20 (x10ms) frames; for G.723, it is 32 (x30ms) frames; for
G.729/G.728, 64 (x10ms) and 64 (x2.5ms) frames respectively.
Please be careful when editing these parameters. Adjusting these parameters
will also change the dynamic jitter buffer. The GXP has
a patent dynamic jitter
buffer handling algorithm. The jitter buffer range is 20 ~ 200 ms.
Grandstream recommends using the default settings provided. Grandstream
does not reco
mmend adjusting these parameters if you are an average user.
Incorrect settings will af
fect the voice quality. Please refer to the Codec FAQ
at http://www.grandstream.com/pdf/FAQ-Codec.pdf for more technical detail.
Layer 3 QoS
This field defines the layer 3 QoS parameter. It is the value used for IP
Precedence or Diff-Serv or MPLS. Default value is 48.
Layer 2 QoS
This contains the value used for layer 2 VLAN tag. Default setting is blank.
Data VLAN Tag
Default is 0. Enabling the Data VLAN filtering will help reduce the load on the
phone, but it isn’t necessary in most environments. This is
primarily for VLAN
filtering where tagged traffic will be forwarded to the DSP.
No Key Entry Timeout
Default is 4 seconds.
Use # as
Dial Key
This parameter allows users to configure the “#” key as the “Send” (or “Dial”)
key. If set to “Yes”, the “#” key will immediately send the call. In this case, this
key is essentially equiva
lent to the “(Re)Dial” key. If set to “No”, the “#” key is
included as part of the dial string.
Local RTP port
This parameter defines the starting local RTP-RTCP port pair used to listen and
trans
mit. It is the base RTP port for channel 0. When configured, channel 0 will
use this port _value for RTP and the port_value+1 for its RTCP; channel 1 wil
l
use port_value+2 for RTP and port_value+3 for its RTCP. The default value is
5004.
Use Random Port
This parameter, when set to “Yes”, will force random generation of both the local
SIP and RTP ports. This is usually necessary when multiple GXPs are behi
nd
the same NAT. Default is No.
32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Grandstream GXP-2000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Grandstream GXP-2000

Grandstream GXP-2000 Bedienungsanleitung - Englisch - 5 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info