470665
33
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
Grandstream Networks, Inc. GXP User Manual Page 33 of 44
Firmware 1.2.5.3 Last Updated: 03/2011
Keep-alive interval
This parameter specifies how often the GXP
sends a blank UDP packet to the
SIP server in order to keep the “hole” on the NAT open. Default is 20 seconds.
Use NAT IP
NAT IP address used in SIP/SDP message. Default is blank.
STUN Server
IP address or Domain name of the STUN server. STUN resolution result will
be
displayed in the STATUS page of the Web UI.
Firmware Upgrade and
Provisioning
Default method is HTTP. Firmware upgrade may take up to 10 minutes
depending on network environment. Do not interrupt the firmware upgrading
process.
Via TFTP Server
This is the IP address of the configured TFTP server. If selected and it is non-
zero or not blank, the GXP will attempt to retrieve a new configuration fi
le or new
code image from the specified TFTP server at boot time. It will make up to 3
attempts before timeout and then it will start the boot process using the existing
code image in the Flash memory. If a TFTP server is configured and a new code
image is
retrieved, the new downloaded image will be verified and then saved
into the Flash memory.
Note:
Grandstream strongly recommends that the user upgrade firmware locally
in a LAN environment if using TFTP to upgrade. Please do NOT interrupt the
TFTP upgrade process (es
pecially the power supply) as this will damage the
device.
Via HTTP Server
The HTTP server URL used for firmware upgrade and configuration via HTTP.
For example: http://provisioning.mycompany.com:6688/Grandstream/1.2.5.3
Here “:6688
” is the specific TCP port that the HTTP server is using; omit if using
default port 80.
Note: If Auto Upgrade is set to No, GXP
will only perform HTTP download once
at boot up.
Config Server Path
IP address or domain name of firmware server.
XML Config File Password
(For
GXP280/GXP/285/GXP1200
Only)
The XML provisioning system allows Grandstream phones to perform
configuration updates via XML configuration files. Users can set the XML config
file password in the web UI of the phone.
Firmware File
Prefix/Postfix
Default is blank. If configured, GXP will request the firmware file with the
prefix/postfix. This setting is useful for ITSPs. End user should keep it blank.
Config File
Prefix/Postfix
Default is blank. End user should keep it blank.
Allow DHCP Option 43 and
Option 66 to override
server
Default is Yes. This allows the device to get provisioned automatically.
Authenticate Conf File
Default is “No”. If set to “Yes”, configuration file would be authenticated before
acceptance. End user should use default setting.
33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Grandstream GXP-2000 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Grandstream GXP-2000

Grandstream GXP-2000 Bedienungsanleitung - Englisch - 5 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info