Bedienungsanleitung Graule ZS 135 (Seite 5 von 14) (Englisch)

782355

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

Graule Maschinenbau GmbH ,

Robert-Bosch-Str. 7, D-73431 Aalen

Tel: 0049 (0)7361 49511 Fax: 0049 (0)7361 49521, e-mail:info@graule.de

• Never work without a safety appliance or with a faulty machine or tool.

• Worn out material supporting tables must be immediately replaced.

• Use only circular saw blades allowed for this type of machine.

• The use of cutting-off wheels or circular saw blades out of high-speed steel (HSS) is not allowed.

• Do not use saw blades being cracked or modified in the shape.

• The machine must have a permanent and safe place and must stand horizontally.

• During repairs and when working to eliminate troubles disconnect the mains plug and wait

until the saw blade stops. The same also applies when removing stuck splinters.

• Damaged cables and plugs must be immediately replaced.

• Always wear tight-fitting clothes. Take off any ring, bracelet, watch or chain when working.

• Wear safety glasses when cutting, to protect against chips being thrown around.

• Sound pressure at work place normally exceeds 85 dB (A).

Therefore, wear an ear protection when working.

• Start working only when the saw blade has reached its maximum speed.

• Do not machine any part being too small or too big for the capability of the machine.

• The machining of round woods or parts with an inadequate work support is prohibited.

• Work only with sharp tools.

• Do not work in a damp or wet environment, or in the surrounding area of combustible liquids or gas.

• Wood dust resulting from cutting the wood is harmful to the sight and sometimes to the

health. If you do not work outside or in well ventilated rooms, the machine must be

connected to a shavings exhaustor with at least a 20 m/s air speed. The same applies when

machining plastic profiles, owing to formation of harmful steams when cutting at high speeds.

• Only an electrical specialist may work at the electrical parts of the machine.

• A regular cleaning of the machine, especially of leaders and material supporting tables

represents a high safety factor. Before starting this operation disconnect the mains plug.

• Standing behind the machine during cutting is prohibited.

8. Starting and using the machine

8.1 Delivery and installation

After delivery, you should examine the machine at once to exclude "transport damage".

Should transport damages occur, inform the carrier at once.

Mount the machine on a sufficiently big table or console. A suitable machine tool table is

available as an accessory.

Fastening is done through the three 9 mm diameter bore holes on the mounting plate.

Turn the 4 screw bolts M 8 down to the table plate and fasten them with the nuts.

If the material supporting table is dismounted, use the 6 flat head bolts to mount it.

Should the machine be equipped with a pneumatic material tension, a suitable valve should

possibly be secured to the table board too.

During transport the saw carriage is locked into place by means of a knurled screw located

at the guide carriage, on the right behind the motor. Loosen the knurled screw and unscrew

approx. 1cm.

If the machine is equipped with a hydraulic feed brake (accessories), this can be pushed

together during transport. In this case unscrew the locking screw which secures the brass

tube in its mounting and push back the brass tube with its mounting as far as the retaining

ring and then pinch it off again.

After releasing the locking device behind the operating handle, the saw unit cab be pulled

forward.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graule ZS 135 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info