Bedienungsanleitung Graupner MC 22S (Seite 143 von 180) (Englisch)

467112

143

Zoom out

Zoom in

Vorherige Seite

1/180

Nächste Seite

143

should now be checked in the »Servo display«

menu:

• The aileron servos 8 + 1 and 6 + 7 should move

exactly in parallel with servos 2 + 5; the aileron

trim lever acts upon servos 2 + 5 and 8 + 1, and

…

• … the Ch1 stick still operates no servos.

Caution:

Check the screen carefully! When the ailerons are

operated, the bars in the »Servo display« should

move in the same direction, but in opposite directions

when the ﬂ aps are deployed.

The next step is to select the menu ...

»Servo adjustment« (page 56)

S e r v o 1 = > 0 % 1 0 0 % 1 0 0 % 1 5 0 % 1 5 0 %

S e r v o 2 = > 0 % 1 0 0 % 1 0 0 % 1 5 0 % 1 5 0 %

S e r v o 3 = > 0 % 1 0 0 % 1 0 0 % 1 5

0 % 1 5 0 %

S e r v o 4 = > 0 % 1 0 0 % 1 0 0 % 1 5 0 % 1 5 0 %

R e v c e n t . - t r a v e l + - li m i

t +

S E L

S E L S Y M A S Y S Y M

A S Y

… and make any changes required to obtain the cor-

rect directions of servo rotation and travel.

This completes the basic programming of the six-

ﬂ ap wing.

Flap settings in different ﬂ ight phases

The ﬂ ap positions can now be programmed to diffe-

rent settings for each ﬂ ight phase.

Start by programming two or more ﬂ ight phases using

the menus »Phase setting« and »Phase assign-

ment«. An example of programming ﬂ ight phases can

be found on page 134.

When you have completed this stage, move to the

menu ...

»Control adjust« (page 58)

TRAVEL

TIME

… which allows you to set the ﬂ ap positions separate-

ly for each ﬂ ight phase.

One ﬂ ap setting for each ﬂ ight phase

If one ﬂ ap position is sufﬁ cient for each ﬂ ight phase,

move to the menu …

»Control adjust« (page 58)

… and select the offset for inputs 5, 6 and 8 to match

the position of the ﬂ aps (“phase trimming”).

At the same time set inputs 5, 6 and 8 to “free” in

each ﬂ ight phase, so that any accidental movement

of transmitter controls assigned to those inputs do not

affect the wing ﬂ aps.

Note:

The offset required may need to be positive or nega-

tive; this depends on the orientation of the servos in

the wings.

However, you may prefer to set up an alternative con-

trol method, such as …

Variable ﬂ ap positions in each ﬂ ight phase using

only one slider (Order No. 4152) or a three-positi-

on switch module (Order No. 4151).

It is also possible to control all six wing ﬂ aps using

only a single transmitter control. In the menu ...

»Control adjust« (page 58)

… assign the same slider or switch module connec-

ted to the transmitter circuit board, e.g. control 6, to

inputs 5, 6 and 8. Ideally this would be a different

transmitter control in each ﬂ ight phase, so that the

correct settings, once found, are retained when you

switch from one ﬂ ight phase to another:

OFFSET TRAVEL

TIME

i4HERMALw

If you are using a switch, set the “deviation” from the

offset point SYMmetrically or ASYmmetrically in the

“–Travel+” column.

However, if you wish to use a slider or rotary knob to

position your model’s ﬂ aps, you should reduce travel

to about 50% or even less in the same menu, as this

gives you much ﬁ ner control of the ﬂ ap trim.

Programming examples – Fixed-wing models

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MC 22S Seite 143

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info