Bedienungsanleitung Graupner MICRO MAGIC 2014 (Seite 8 von 15) (Englisch)

637252

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY

#0057088

Keine Haftung für Druckfehler. Technische Änderungen vorbehalten! No liability for printing errors. We reserve the right to introduce

modifications. Sous réserve de modifications! Nous ne sommes pas responsables d’éventuelles erreurs d’impression! 11/2006

waterline, or inclined slightly upward towards the bow.

IMPORTANT: it must not hang down. When you have

obtained this position, glue the bulb to the keel using

UHU acrylit or thick cyano. Allow the adhesive to cure,

then cut two 1.5 mm Ø retaining pins (part 51) from the

steel wire supplied, and pass them through the keel

bulb and the keel to retain it.

• If you do not wish to use the keel bulb fairings, you

should finish the keel using the following procedure:

file the surface of the bulb as even, smooth and

symmetrical as possible, and fill any remaining holes

(e.g. using Order No. 924). Sand the filler back flush

when hard. NOTE: the smoother the surface of the

keel bulb, the lower the water resistance; careful work

pays dividends here.

• Alternatively you can fit the keel bulb fairings (part 52).

In this case you must sand away the lead bulb until the

shells are a snug fit round it.

• Screw the keel to the hull using a washer (part 43) and

the retaining nut (part 53); this holes the hull in a more

stable position in the boatstand for the following

stages.

• The rubber gasket (part 54) is glued in the canopy

(part 55) using cyano. Don’t cut the cord to final length

until you are just about to join the ends.

• To complete the mast (part 56) you require the

aluminium mast sleeve (part 57) and the hardwood

dowel mast base (part 58). Sand the hardwood dowel

until it is an easy sliding fit inside the mast, then glue it

in the end of the carbon fibre tube. Sand the end flat,

and round off the end slightly. Cut the aluminium mast

sleeve to a length of 115 mm, and insert it in the mast

opening.

• Slide the main boom bracket (part 59) and the mast

plate (part 60) down over the mast sleeve until they

rest on the deck. Check that everything is central, then

fix the mast plate to the deck using fillister-head screws

(part 33).

• Assemble the main boom swivel bracket (part 61), the

washer (part 35) and the swivel axle (part 62), and

check that the axle rotates very freely; if not, sand it to

ease the fit.

• Glue the main boom (part 64) in the main boom sleeve

(part 63). Screw the clamp nut (part 66) into the

depressor (part 65). TIP: the correct thread is on the

end with the notch. Push a large annular clamp (part

67) onto the main boom, fit one end of the depressor

into the annular clamp and secure it with a retaining

screw (part 68). Don’t tighten the screw fully at this

stage; it must be possible to adjust the position of the

annular clamp on the boom.

• Screw the main boom to the main boom swivel bracket

using two screws (part 68) and two retaining nuts (part

69).

• Fit the jib hanger (part 70) on the mast and glue it in

place at a point about 95 mm from the top of the mast.

The masthead fitting (part 71) can now be glued to the

top of the mast. IMPORTANT: check that the

masthead fitting is exactly in line with the jib hanger.

• Cut the backstay (part 72) from the white polyester cord supplied. Cut a piece from the large loop of one

wire hook (part 73), as shown in the drawing, and apply a drop of cyano to the point where the two loops

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MICRO MAGIC 2014 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info